Whether you are changing a flat tire, installing a new fancy off-road. Knowing how to remove and install a spare tire on any vehicle is always a good idea before you need to in the event of an emergency. Connect the two equal-length rods together to make a long rod. This releases the license plate bracket, which is attached to the front side of the carrier. There's no one solution to getting the tire to come down, so this article will give you steps to try in the order of increasing labor time. You then have to flex the wheel support on the end of the cable sideways to fit through the hub of the wheel to get the spare out. Removing the spare tire 1.
Since the bolt heads are close to the center of the spare tire, letting the air out of the spare can give you more room to work in. The tools you will be using include the wheel wrench A , wheel blocks B , extension s , socket end C , handle jack end D , and jack E. Finding a FrequencyTurn on the Chevy's radio. Depending on your van, either lift up on the cargo bin door in the rear and you will see a hex shaped nut or in the 2nd row seats there is a little circle that is cut out of the carpet with the same hex shaped nut undeerneath. Also, Caution, I learned the hard way that the original jack is not very strong. Putting too much weight on your tires will overload them, and can cause tire damage, premature tire wear or even tire blowout.
It will either fail or not and the scanner operator will see it. You will notice that one end of the tool has a flat end. Remove the eight bolts on the back of the spare tire carrier using the lug wrench. On a day when you have some free time, it's recommended to try to get the spare tire down so you know whether it's working or not before you actually need to get it down. Turn the wing nut counterclockwise with your hand to detach the tool set. This article applies to the Chevrolet Silverado. Tilt the retainer at the end of the cable when the tire has been completely lowered, and pull it through the wheel opening.
Difficulty:ModerateInstructions Things You'll Need Wrenches Torx wrench Open both of the truck's front doors. Keep in mind that Tire Pressure Monitoring System does not replace routine tire pressure check and maintenance. Most manufacturers of light Vehicles install the spare tire underneath the rear cargo bed to save room in the bed itself. However, depending how the tire was installed, this process can either be very easy or an annoyance if the valve stem is on the top. The transmitter functions will work up to 20m 65 ft away from the vehicle. Modern Vehicles and Vehicles also owned by Vehicles are almost identical and are manufactured on the same assembly lines, although the Vehicles sports unique front end styling. One of the best features of the Equinox is the ability to remove the back seat from the vehicle for more storage.
Maintain proper 2005 Chevrolet Uplander winter tire pressure by adding air to your tires as needed to the recommended tire inflation levels. Loosen the wing nut that holds the jack in a counter-clockwise direction. To access the spare tire on older Vehicles you had to crawl under the bed, loosen the bracket, and lower the spare tire by hand. Attach folding wrench to extension, insert 'chisel' end on an angle through the hole in the rear bumper and into the hoist shaft. Difficulty:EasyInstructions Front SeatRelease the seat belt from the front seat by sing the release latch behind the trim panel on the seat's side. This article brings those options to one place for your viewing.
Then consult your owner's manual for the replacement procedure. This article applies to the Chevrolet Silverado 1500 1999-2006. How to reset tire pressure warning light for 2005 Chevrolet Uplander? This article applies to the Chevrolet Silverado 2007-2013. Remove the top bolt and locking pin as you mentioned , then remove the headlamp housing by pulling it or pushing it from behind straight forward to release the friction pressure clip located near the outside edge of the housing. Find out how to change it with this helpful article. Insert the long rod end of the tool into this hole.
ConsequencesAside from the annoyance factor, the inability to access your spare tire will result in havi Whether you have a flat tire on your Chevy truck that needs to be replaced or you want to install an aftermarket tow hitch, you're going to have to remove the spare tire. Be sure the socket end of the extension C connects to the hoist shaft B. It may be necessary to lift one end of the tire to disengage the retainer Jul 12, 2009. Removing the SpareThe factory jack handle is required to remove the spare tire from the S-10. First, you need tools: 1. In the bag, you have two tools.
The ends have fittings that allow them to connect. Installing them, however, is another matter. If using a magnetic antenna, simply stick it in the appropriate place on the Uplander's roof. The spare tire on the 2007 model was stowed underneath the car and came equipped with a hoist and cable to lower it to the ground. You can find a bucket seat that will fit your Uplander by visiting your local scrap yard and getting a seat that comes from an Uplander. The same is true when you Put your spare back. Pro Tip You can also find this information in the owner's manual.