The part should come with torque specs as should any bolts or screws you buy. Please take into account that the Honda 0 to 60 times and Quarter mile data listed on this car performance page is gathered from numerous credible sources. Generally speaking, long bolts are often installed on raised platforms while short bolts are often recessed. . This article applies to the Honda Civic 1992-2000. Hatchback Introduced in 1992, trims available in the hatchback body style in the U. Tightening your bolts too much or not enough can cause a part to fail, and depending on the part, can put your life and the lives of the any passengers in danger.
Zero to 60 times does not guarantee the accuracy of any of the Honda 0-60 mph times. Another example is the intake manifold. When this happens, the head can often snap off, which means deal with an extremely tight bolt that can't simply be unscrewed. For example, if the final torque should be 100 foot-pounds, then tighten to 50 foot-pounds first, and then repeat the process until you've tightened to 100 foot-pounds. An easy way to do accidental damage is to over torque or under torque bolts and screws. At its introduction in, it won the Car of the Year Japan Award for the second time. In other markets Japan, Peru the Si received the 1.
How can I tell where to reinsert screws and bolts? So you have a really. Common Questions Why should I care about torque? Does the order in which I tighten bolts or screws matter? This article applies to the Honda Accord 1990-2002. There are a number of. It can crack if the engine's bolts aren't tightened in the proper pattern. This generation of Civic used lightweight materials to create a fuel efficient economy car. Take pictures while working to remember which bolt goes where when reusing them.
Refer to the service manual for a complete list and be sure to confirm the torque specs on any new part or component you buy and plan to use. Typically, you can feel it in your torque wrench if you've overtightened or stretched a bolt too far. For the same reason it's always a good idea to use new bolts when working on the engine. If you don't replace these bolts and screws in the right place, you can damage the part. Not following the prescribed pattern risks having a wheel with loose lug nuts. This article applies to the Honda Accord 1990-2002.
Some components use short and long bolts and screws. Most parts come with bolt-tightening torque specs, and your owner's manual should have this information too. Bookmark us and keep checking back for Honda cars 0-60 mph updates, since we constantly upload new 0 to 60 mph and quarter mile statistics. You may want to use a torque angle gauge to make sure you're not over tightening. Most owners manuals include information about the order in which to tighten bolts and screws during reassembly. Check out this handy, step-by-step guide to learn how.
This article applies to the Honda Accord 1990-2002. In fact, several factors affect torque specs. Always refer to the service manual when possible to be sure the bolts being used are the correct length. Manufacturers require specific patterns when tightening bolts and screws in order for parts to be properly seated. This is called torque-to-yield, where you tighten a bolt to a certain point and then it further.
That way, the bolt and screw threads firmly attach to the matching threaded hole or nut. B Series Torque Specifications Please note that this is not a complete list of torque specifications for all parts and components of your Honda Civic. A left-hand drive version of the Civic Coupe was released as a limited edition in Japan, imported from the United States, to celebrate the tenth anniversary of the Honda Primo dealer network in 1994. D Series Torque Specifications Figure 2. The new Civic was larger than its predecessor, had a more aerodynamic body and the wheelbase was increased to 257 cm 101.
The four-door wagon was not updated for this generation platform, and continued to use the previous generation internationally until February 21, 1996, when it was replaced by the Honda Orthia and Honda Partner sold only in Japan. How can I tell if I've over-torqued? Not only does this increase your repair and reassembly time, but it increases the risk of damaging the car trying to remove the broken bolt. Compared to the previous generation, the cowl was raised, which allowed for more suspension travel. So you have a really. There are a great deal of factors that affect the Honda cars 0-60 stats, so different sources may test the same vehicle and each may arrive at a unique 0-60 mph and quarter mile result. There are a number of.
Do I tighten to the accurate torque spec all at once? An overtightened bolt will suddenly takes less effort to turn the bolt. This article applies to the Honda Civic 1992-2000. This article applies to the Honda Accord 1990-2002. In Japan, a four-door sedan was introduced called Japanese: Civic Ferio, sold at Honda Primo dealerships, while a more upscale version was called the Honda Domani sold at Honda Clio. The most common example is the criss-cross pattern required when tightening the wheels. In Canada, it was rated by Transport Canada fuel consumption estimate: 4. Si: The Si model replaced rear drum brakes with discs, added a power moonroof with tilt, cruise control, a dashboard clock, a 9K tachometer with a 7,200 rpm redline, plastic wheelcovers on 14 inch wheels, power side mirrors body coloured, beginning in 1993 , body-coloured door handles, and a 125 hp 93 kW 1.