Lesser trims were often paired with the 2. Pick up a Haynes manual on E-Bay or a auto parts store. Problems with the rear parking brake that was incorporated into the disc brake design were common. Move the starter around a bit until you can see the nuts holding the wires on, and then detach the wires. Answer You can go to ford online and they may provide an online manual.
The upside is that it was able to seat 5 adults in relative comfort. It was available with the 4. Lesser trims were often paired with the 2. All cars rust up here with the salt and sand in winter. Pull up the flap so you can see the starter. The Blazer and Jimmy appeared as 1983 models. This sub-model lasted until 2004.
The visibility around the vehicle was adequate, I never had a problem with spacing my vehicle. Be sure to do this out side as it will make a mess in the garage. Nothing to write home about. The drivers seat went back far enough to sleep comfortable. Off roading was suitable, the balance of the truck maintained itself when driving across an incline and on trails. At the same time, a Blazer Xtreme only on the 2-door model was added to the lineup, based on the S10 Xtreme. The back seat also folds down to create more room if needed.
In 1999, new folding mirrors replaced the old folding mirrors. The S-10 came with two engine choices. Click on the link below Click on Owner Guides The owners manual can be viewed on-line Locate the 2 plugs on the transmission. In the , retail sales of two-door Blazer models ended in 2004; all other models were sold until April 20, 2005. Got mine at a junkyard they do have them and can check with other junk yards to find the one you need. The interior does rattle a bit and feels a little cheap and plastic, but everything still works.
It is manually aligned, but it takes a professional with the proper equipment, knowledge, tools, and skill. The drivers seat went back far enough to sleep comfortable. The head lamps were canted well and I had no problem with visibility. Depending on the configuration, standard towing capacity stood between 2000 pounds and 5200 pounds. I was able to fit 5 comfortably.
The label on the compressor top will verify this. The 1994 S-10 Blazer and Jimmy seem to have used R-12 until the end of their production run and subsequent replacement with redesigned 1995 models that looked like new-for-1994 pickups. During the summer the seats wouldn't deal well with moisture, often being damp during the summer months. Maximum payload capacity ranged from 1000 pounds to nearly 1500 pounds. Body trim included also black plastic fender flares, front fog lights and spare tire carrier on the tailgate. The V-6 suffered from heat-related head failure, computer-controlled carburetor issues, and low torque. The head lamps were canted well and I had no problem with visibility.
The roof rack was minimal at best. Not having to put on chains using all weather tires , I never broke traction and never had a problem with body roll. The back end is rusting a bit, but that is to be expected in the northeast where I live. The interior quality was standard. The cooling system was a constant hassle.
It currently has close to 300,000 miles on it and I drive it every day. Brakes The S-10 brake system was originally a front-disc, rear-drum setup, which changed for the 1998 model to four-wheel discs. Two-tone paint was also a popular option for the model back then. The Trailblazer's headlamps, which featured daytime running lamps, would be available on various Blazer models until production ended. The crew cab configuration automatically meant having a truncated box that isn't of much use for carrying long or bulky loads.
Screw in top plug and you're done. Looking towards the front of the Blazer you will see two bracing rods coming from the fro … nt and bolted to the aluminum housing between the engine and transmission. Engine The early years of the S-10 model were focused on creating competition for Asian small trucks. S-10 customers had a choice between two-wheel drive and four-wheel drive. The steering colume is in the way to use a socket.