This is done to meet changing engine oper- ating conditions. Drain lubricant to the correct level. Refer to Group 8A, Battery for The battery temperature sensor is located under procedures. Find your 2000 Jeep Cherokee repair manual right now at Chilton. Water pump impeller loose on 8.
A basic knowledge of mechanics, including the proper use of tools and workshop procedures is necessary in order to carry out maintenance and repair work, satisfactorily. Other trademarks used throughout this web site are the property of their respective owners and are used for identification purposes only. The manuals give comprehensive information on your parts for Jeep and much more. Installation section of this group for the procedures. Unplug the wire harness connector from the relay Fig.
The shims are placed under the inner pinion bearing cone Fig. Tighten the hub nut to 237 N·m 175 ft. Information in this manual is divided into groups. Use Remover D-149 and Handle C—4171. Be certain that you depress the defog- There should now be continuity between terminals ger switch at least twice to confirm that the system 30 and 87, and no continuity between terminals 87A is turned on during this test. All of Chilton's online content for the 2000 Jeep Cherokee is updated monthly, so you'll have the most recent information on hand for any Do-It-Yourself project.
Save time and money by doing it yourself, with theconfidence only a 2000 Jeep Cherokee Service Repair Manual canprovide. Refer to Ducts And Out- umn upper shaft spline using a steering wheel puller lets in the index of this service manual for the loca- Special Tool C-3428-B. Be sure bearing is properly secured to release fork. This Service Manual has easy-to-readtext sections with top quality diagrams and instructions. Tighten the mounting screws to 2. This will provide case-to-ring gear bolt hole alignment. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure.
Crankshaft Position Sensor Bolts sensor mounted with 2 bolts. Remove the sockets and bearing cap that was partially forced out of the yoke. Also, the gasket is installed dry. Use of this web site constitutes an agreement to these Terms Of Use. Detailed illustrations, exploded diagrams, drawings and photos guide you through every service repair procedure. Foreign objects imbedded in 1.
The ohmmeter is used to check A damaged wheel can cause shudder, vibration and continuity between the pin terminals Fig. All diagnostic and repair procedures are covered. See Wiper Arm in this group for the procedures. Has a Diagnostic Trouble Code 1. This Service Manual has easy-to-read text sections with top quality diagrams and instructions. If the solution 3 Connect a tachometer and an engine ignition is clean, drain the coolant into a clean container for timing light timing light is to be used as a strobe. All Manuals Are Windows and Mac compatible! Install the hold- down clamps and tighten the tool turnbuckle finger—.
Tighten the lower switch water shield and bracket screw to 1. Tighten mounting bolts to 23 N·m 17 ft. Factory highly detailed repair manual's, with complete instructions and illustrations, wiring schematics and diagram's to completely service and repair your vehicle. Clutch Housing to Transmission Bolts. Remove side gear, clutch pack retainer, and clutch pack.
Fit the open trunnions into the link yoke bores and the bearing caps into the centering kit Fig. Tighten mounting screw to 3. If a new gear set is being installed, note the depth variance etched into both the original and replace- ment pinion gear. It covers every single detail. The release fork is actuated by the hydraulic slave cylinder mounted on the transmission housing. Axial The clutch inspection chart Fig.
Spark plugs with this condition must be replaced. Trust 2000Jeep Cherokee Service Repair Manual will give you everything youneed to do the job. Always use the not pull on the instrument cluster by the lens correct bulb size and type for replacement. Only remove enough insulation to solder in the new diode. These manuals have plenty of pictures and diagrams to make the entire repair process easy for you. The clutches will have radial grooves on the plates, and concentric grooves on the discs or bonded fiber material that is smooth in appearance. Loose or worn wheel bearings.
You get everything you will ever need on one easy-to-use cd-manual. Tighten the upper switch mounting screws to 2. This Service Manual has easy-to-read text sections with top quality diagrams and instructions. Refer to Group 21, Transmission and Transfer Case for procedures. Ensure anti-rotation tab is positioned in slot on hood inner panel. The conventional pyro- charge the gas it produces directly into the cushion technic-type inflator assembly is mounted to studs on when supplied with the proper electrical signal.