Also, the upper radiator hose also must be disconnected to get the fan shroud out. If the clearance is out of specification, replace the transmission hub sleeve no. To remove the window crank if applicable push the washer back toward the panel while pulling the crank toward yourself to expose the metal safety clip. Should you have any questions or concerns about your Shift Select transmission, our Product Support Team is only a phone call away. If you have someone working with you from above when positioning the new one, it would help. Some transaxle fluid will leak out.
Hint : do not set both openings of the shifting key springs in the same position. Any good auto parts store sells these plastic pumps at nominal prices. This process pushes the cylinder back out so that there is pressure on the brake pads when you press the brake pedal. Remove the bolts, if applicable. I did it out on the street with the car safely jacked up.
They pull out easily, if you have trouble use a screw driver. With new micro-laser technology gear tooth production tolerances have been reduced 50%. They are together on the bottom and look similar. Both are good options but the best option for you depends on the transmission problem, the year, make and model of vehicle, the mileage and the vehicle value. There are 4 bolts and one plastic fastener to be removed in total with air-filter assembly. No fluid is leaking but essentially, when I try to tighten it eventually loosens so that I can turn it by hand so I tightened it to just until it gives.
Get a Chilton repair manual for that vehicle, it's got a lot of information about starter removal. Just simply follow the spark plug wires to find all 6. Otherwise, the packing fipg material must be removed and reapplied. Inspect transmission hub sleeve no. A bit surprised that it striped so easily. Pull the tension off the belt, and take old belt off.
The second bolt is accessible from the top of the engine, only after the air-filter assembly is off to the side. Install gear shift fork no. It will say Transmission funnel on it. Notice : ensure the file lapping compound is completely washed off after rubbing. Disconnect the electrical connections to each individual ignition coil over the spark plugs. Sst 09612—65014 09612—01050, 09612—01060 46. Hint : align the mark on the reverse idler gear shaft with the bolt hole shown in the illustration.
If the clearance exceeds the maximum, replace the gear, needle roller bearing or shaft. And please rate it 5 stars if you found it useful, which … I'm sure you will. There is a ring clip holding it inside the transaxle that needs to be dislodged. Used transmissions, since there is no way to know how many miles are on them, may fail at any time. Remove t … he cables from the starter and then unbolt from car and remove. Try not to bre … ak anything.
The vapor pressure sensor and the vsv for the canister closed valve ccv are used to detect abnormalities in the evaporative emission control system. After you are done, make sure that after you start the car for the first time, you press the brake pad all the way to the floor and let it out slowly. After you drain it then you can remove the pan to change the filter. Hint : using a waste to prevent the snap ring from being scattered. A little force is necessary but not enough to break the plastic. You have to buy the Transmission Oil Filter and a strap loacated in all the edge of the door where the filter is located.
Remove the plastic elbow from the intake and air box. . Use a brass drift and hammer to separate left side axle shaft from transaxle. Final drive ratio is 2. One of the nice features of the Echo is that it has a transmission fluid filter.
Remove the door panel by prying it off screw by screw. What kind of warranty coverage are you looking for? Install gear shift fork shaft no. Remove fan and generator v belt 4. Disconnect wires from old starter. Notice : do not set the reverse restrict pin assy in incorrect orientation.
Hint : using a waste to prevent the snap ring from being scattered. There is a drain plug with a female Allen hex on the bottom of the trans pan. Pry outward on the tab with a small standard screwdriver located on the electrical connector to release the connection from the coil. Remove gear shift fork no. Do remember to disconnect the battery ground wire first.