Pull lever up to adjust seatback. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle. Instead, gradually decrease your speed. Always remember to turn on your headlamps at dusk or during inclement weather. . Determine which magnetic zone you are in by referring to the zone map.
See the owners manual for the correct fluid. After the last track has been completed, the first track of the current disc will automatically replay. Speed sensitive volume if equipped With this feature, radio volume automatically changes slightly with vehicle speed to compensate for road and wind noise. When changing the air filter element, use only the Motorcraft air filter element listed. If fluid runs out, it is already full enough. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. Tachometer if equipped Indicates the engine speed in revolutions per minute.
If this happens, reinsert the disc holder back into the magazine while pressing on the lever A. Refer to Electric automatic temperature control in the Climate controls chapter. Sometimes it's near the transmission, like close to the center of the engine. Pry support bracket slightly to gain access to lower starter mounting bolt. Do not pull on the outer joint or you will pull the inner joint apart. Return to the center position to lock mirrors in place.
Route the tether strap through the loop directly behind the child seat. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for further instructions to secure the. Rewind The rewind control works in tape mode. Refer to Lubricant Specifications in this chapter. Place the gearshift in N Neutral automatic transmission or depress the clutch manual transmission.
Stock Number: I81506252G Fits: 2002 Ford F-150 Automatic Transmission; 8 Cyl, 330 cid 5. Pull control on the side of the seat to release seat cushion from the load floor position. Tilt nose downwards and lower starter motor far enough to access and remove nut that secures battery positive cable wire harness connector eyelet to solenoid battery terminal stud. Pressing the control for more than three seconds results in fast forward action. You do not need to remove axle from car, just let it hang. Disconnect and isolate negative battery cable.
Refer to Turning speakers on and off. Do not hold for longer that 30 seconds. Upshifts can be made by shifting to 2 Second or to Overdrive. To install the floor shift housing to the floorpan reverse the above instructions in order 6, 5, 4. If you have to resort to brut force, be carfull prying on the aluminum and apply force on both sides at the same time.
When the fuel filler cap is properly re-installed, the light s will turn off after a period of normal driving. Keep a close eye on the fluid level for the first few trips and add a little fluid as necessary. Pressing the control for more than three seconds results in fast rewind. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Do not drive in reverse over a hill without the aid of an observer. Be careful when getting the mounts back on, that the engine and transaxle settle down perfectly into the mounts, so you have no vibration issues. I am going to assume your are removing the tranny in order to change the clutch? Buy a recycled 2002 Ford F-150 transmission and save thousands of dollars.
Allow the vehicle to sit for at least eight hours without starting the engine. This information will assist Ford Motor Company in servicing the vehicle and in helping to better understand real world collisions and further improve the safety of future vehicles. Be sure the belt webbing is not twisted. Install the bulb socket in the foglamp by turning clockwise. Disconnect the four nuts that attach the housing 6. If the dealership employees cannot help you, they can direct you to the nearest Ford affiliate office. Clean all traces of gasket and sealant from the mating surface of the transmission.
Make sure it goes in square. May 14, 2011 You will need a floor jack and two jack stands. Wait until the safety belt warning light turns off. Do not hang any type of accessory or accessory bracket from the plug. Make sure that the seat is relatched into place. Fuel vapor is extremely hazardous under certain conditions. However, the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode.
Note: In the illustrations, lightning bolts are used to designate the assisting boosting battery. Place the gearshift lever in N Neutral automatic transmission or depress the clutch manual transmission. Or after 2nd gear the rpms run up to 25-3000 then it shifts. Clean all traces of gasket and sealant from the mating surface of the transmission. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted. See your Ford or Lincoln Mercury dealer.