Comes with a 30 day warranty. You will want to replace the air filter while you have things opened up to replace the resistor. Loosen the clips holding the front edge of the water shield with a screwdriver. You will want to replace the air filter while you have things opened up to replace the resistor. This includes the full wiring harness, so if you wish you can just plug it in. We also provide inexpensive and guaranteed 3 day, 2 day, and Overnight shipping options, so if you need your Blower Motor Regulator tomorrow, eEuroparts.
The resistor pack is shown below with a blue plastic frame. Remove the rubber moulding along the edge of the bulkhead and loosen the clips on one side. When I turn the car on in the morning, the heat works. However I don't show what I did under the dash which was the trickiest part. Loosen the two front connectors above the filter cartridge. At the same time, lift the fan and angle it towards the dismantled stay in order to remove it from the bulkhead partition space. Unplug the contacts from the plate and cut the cable tie.
Once the screw holding the resistor pack in place is removed, the orange and brown wires that are connected to the resistor pack may be removed. Remove the frame around the ventilator fan, 2 clips and 2 nuts on front edge. Saab calls it Ventilating Fan Control Unit resistor unit , located on driver's side of heating and ventilating unit, near firewall. I think it's located under the dash by the cabin filter and runs to the blower motor. Do you have a problem: heater fan not working? Complete shipping and return policy information can be found in our.
These can also cause blown fuses. The blower motor resistor is located under the cabin air filter. Best access is by closing the hood. This time, he instructs us on how to solve the problem of the Blower motor in Saab 9-3. Unsolicited commercial postings are not allowed no spam. Click here to see all the! Remove the 3 data link connector screws and detach the leads to the floor lighting.
If you would like to return an item or have questions about the process, please and one of our customer service experts will be happy to help. Lift off the water shield. But that is not the case here. Remove the wiper arms with special tool 85 80 144 Puller, windscreen wiper arm. Blower Motor Resistor Removal and Replacement 1.
The item must be new and in its original manufacturer packaging to be eligible for a cash refund. This will allow you to see if the fan motor is seized. Each of these wires has a single termination, and the connectors are different sizes to ensure that the proper connection will be established. Complete shipping and return policy information can be found in our. Not sure if i have to remove the blower motor in the process. If there is anything you cannot find in our catalog please and our knowledgeable customer service team will help you locate the part you need, fast.
Here is a link of the part which needed to be replaced:. In this case, it is likely that the resistor pack used to limit current to the blower motor may need to be replaced. Once the screw holding the resistor pack in place is removed, the orange and brown wires that are connected to the resistor pack may be removed. Free the cable harness from the cover over the ventilation fan fastened with clips. The item must be new and in its original manufacturer packaging to be eligible for a cash refund. Each of these wires has a single termination, and the connectors are different sizes to ensure that the proper connection will be established. If the original item or suitable replacement part is not available, then this warranty is void.
We also provide inexpensive and guaranteed 3 day, 2 day, and Overnight shipping options, so if you need your Blower Motor Regulator tomorrow, eEuroparts. He is a frequent contributor to thesaabsite faqs pages. So, if you happen to your heaters stops working, you would need to unblock the seized motor, or to replace it. Unsolicited commercial postings are not allowed no spam. If so how hard is it ot replace. Connect the two single wires then the connector with multiple wires into place. For usage guidelines, see the.
Please remember that you are not anonymous. I managed to get the removal procedure for the resistor and here they are. Pull up the wiring harness including rubber seal and cut the cable tie. Once the cabin air filter is removed, a screw that holds the blower motor resistor in place may be removed. This is a good used unit removed from a recent crash damaged car. Successful operation of the blower motor resistor should allow one to adjust the fan speed to operate at different air flow speeds. Blower Motor Resistor Removal and Replacement 1.