The vehicle was taken to the dealer and it was determined that the crank shaft position sensor failed and needed to be replaced. Then just twist the brake light socket to the left … and pull it out to get to the bulb. Using a spark plug socket, remove the old spark plug and install a new one in it's place. If our prices don't convince you, we also want to make sure that you can hear from car part experts, so we have reviews you can browse through on our sites to get you peace of mind. Starting with the fist spark plug on the left: Remove the spark plug cable by pulling straight up on the insulated connector. This releases the entire assembly. In the past, I have replaced the battery and had a tune up performed by the lester glenn Hyundai dealership.
Unplug the wire connector from the crankshaft position sensor. It said it was the crankshaft sensor. The top of the oil filter will be facing to the left, pointing toward the passenger side tire. Deal with it you moron! There is no variation in valve timing of the exhaust cam because the exhaust camshaft is driven by the timing belt. It has a triangular push-in and it has to go just right so take note of how it comes out. Crankshaft Position Sensor The crankshaft position sensor is located at the front of the engine near the timing belt. Otherwise the coo … lant goes everywhere when you drain it.
Note: This engine has 2 coils. Should have 2 screws holding it in place. Repeat same procedures for spark plugs number 3 and 4. Using a spark plug socket, remove old spark and install a new one in it's place. The change in the magnetic field cause the voltage from the sensor to change. Hyundai needs to expand the perimeters of the recall to resolve this problem.
My car is now being fixed at a Hyundai dealer. All of our Crankshaft Position Sensors are guaranteed to fit if you use enter your Hyundai Santa Fe into your Year Make Model selector. Lift the coil straight up removing the insulated connector from spark plug number 2. I just had to fix mine. Consumer have confidence in the vehicle and fear of it stalling in the center lane where there is little options except getting hit and possible getting seriously injured. Replace a Hyundai Santa Fe tail light You'llhave to raise the rear compartment door fully. Repeat same procedures for spark plugs number 3 and 4.
I bought the Santa Fe in service several times for this problem to be told they can not find the problem. They are located above spark plugs number 2 and 3 from left to right. Remove the 4 12mm bolts from the decorative plasitc engine cover. Common mounting locations include the main crank pulley, the flywheel, or occasionally on the crankshaft itself. P0335 Hyundai Description The Crankshaft Position Sensor also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Sounded like it wasn't getting enough fuel. If the vehicle is in great shape, the cost of replacement is still less than a couple of payments on a new car.
Mechanic determined that the crankshaft position sensor needed to be replaced, and replace it. To access the second spark plug from the left, remove the electrical connector and the spark plug cable wire from coil number 1 and then remove the 2 12mm bolts that secure the coil to the engine. The only time that filter would be replaced is if the transmission were overhauled. If it was on one vehicle year why wouldn't my year be covered. Once you have that much labor into it, the timing gelt and water pup are very close.
Lift the coil straight up removing the insulated connector from spark plug number 2. The problem is more noticeable when it is raining or humid out. When the crankshaft position sensor on a Hyundai Santa Fe is defective, you may experience hard starts, stalling or the engine may not start at all. In addition to robbing you of fuel economy and performance a faulty Knock Sensor can cause expensive damage to your engine. The crank sensor can be used in combination with a similar camshaft position sensor to monitor the relationship between the pistons and valves in the engine, which is particularly important in engines with variable valve timing. Oct 31, 2009 There is a very good chance the Crankshaft Position Sensor needs replaced. Don't get attached to cars.
You can check the voltage range it puts out, and determine if it's faulty or not. For more information: We've got a wide rang of top-quality Hyundai Santa Fe Crankshaft Position Sensor of all the best brands in the industry at an affordable rate. Have parts delivered straight to your home, or find the nearest Advance Auto Parts store to check out our Crankshaft Position Sensor stock in-person! Use a 10mm wrench to remove the cover. Push it back and there is a cap that unscrews which holds the wires and socket he is talking about. Spark plug number 2 is located directly under the coil. It is behind the timing belt cover mounted above the crankshaft sprocket. And, I am not sure, but I doubt that my car is worth much more than that.
The car all of a sudden shut off on me. Nissan has a recall campaign on the crank angle sensors. The part is easy to replace two screws, typically , and can be bought at a car part store. May have same problem I have a 2002 Sonata. You probably know you have an interference engine and that the belt is just about due for replacement.