If you have an extended warranty, it is possible this may be covered. Blowing the lines out as I've read elsewhere is a good thing to do, it is free and it might fix it. They also have a mark on the outside which should line up with the retention brackets that you push the hoses into. The reason I didn't realize this is I didn't clear the code, which was intentional on my part since I wanted the code to still be there in case my repair didn't work so the shop could still see it if necessary. . The contact was able to coast to his residence.
Most of the time, it has happened while I am driving in and out of parking lots, at low speeds. Part number 14596-1P101 2 any thing particular to look out for or keep in mind when removing the old one? The contact stated that he attempted to restart the engine several times before it eventually started and functioned normally. Thanks, Michelle I am so sorry it took me so long to get back to you. The current mileage was 99,379. The mechanic told me this was a common problem with Nissan. The contact was also informed that the vehicle was not included in recall 06V242000 engine and engine cooling. We can see that the solenoid only moves sometimes, and the only way to check if it's the actual valve is to rip it apart.
Also, except when idling and during low engine coolant temperature, this system opens the swirl control valve. So how do you find out what problems are occurring? At the first moment, the service engine light came on, then all the warning lights and the car stopped. I have a check engine code of P1138 which is the swirl control valve. Go through the following and see if you can come up with anything. Nissan thus far has been successful in not accepting responsibility for the gasket defect, a typical pattern of auto manufacturers.
The only reference I could find on this site was a reference to a P1130 code close but not the same thing. He pointed out to me the valve on the right of the manifold and it is fed by the coolant system. If I wait a few more months before i replace it, will it cause more problems down the road? Roadside assistance was called to the scene and the vehicle was towed to an independent mechanic for inspection. I found one on a website for sale but its for the 1. There are 6 of them. I blew out the pipes and all. You can re-set the code by using a code reader, or just by disconnecting your battery for 24 hours - that's what I did.
It is a replacable valve easy to work on. I don't usually work on cars but I've done plenty of stereos, alarms, navigation systems, etc. Check resistance between intake valve timing control solenoid valve terminals 1 and 2 under the following conditions. Make sure you can blow through it in the direction of flow. I am scared to death to drive my car. He attempted to duplicate the failure, but could not.
I have a 2005 nissan that had other engine codes and I have asked them to check swirl valve but I am getting run around from my dealer. I was on an 8-lane very busy road in a middle lane. Aug 08, 2008 I have been working on a 96 nissan truck for three years for an evap code and swirl control , I finally just made sure the swirl control solenoid operated properly then disconnected the vacuum hose from the swirl control actuator and plugged it. This solenoid valve is used only for diagnosis, and usually, remains opened. There are potentially other symptoms as well. Nissan said that all was fine, but again last week on Friday Oct 2nd the problem happened. I wonder if it's possible that I got a bad part? Failure is so intermittent and non-repeatable that no effect troubleshooting can be performed.
Opened a case with Nissan for assistance and absolutely none was offered. Any recomendations as to location of valve and repair would be great. This is a safety issue! Then the labor to do this repair is around 3. Make sure the fuel cap is tight. Thisi s a problem my daughter had on her 2003 nissan and it was under a voluntary recall so if you bring it to dealer and tell them they have to replace swirl Valve free. Can someone please confirm if socket diagram matches with terminal number from the actual picture? In this condition, this system tends to increase power by improving intake efficiency via reduction of intake flow resistance, intake flow. Next some reading told me to blow out the vacuum lines with air--they get clogged up.
The vehicle was then taken to an authorized dealership where the contact was informed that the crankshaft was defective and needed to be replaced. After ordering and installing the new swirl control valve I still had the same issue. If I were doing it again, I'd try another free fix before I bought a new one. The valve is installed in the intake manifold, and the actuator is connected to the rear end of the valve shaft. Any comments would be nice.