If so, how do you do it and what do you do it with? After fixing the problem, I realized the truck should never have gone into limp mode. My vehicle has been at the dealership for eight days. There was no type of warning lights, it would rev up till it reached 3500 rpm and then it would just cut out like it had hit the rev limiter. The test for 12 volts is much more valid if it is done with the pump plugged in and you back-probe the wires through the rubber seal in the connector. We're here to help you find that perfect Fuel Pump for your Nissan Titan. Loosen the hose clamp on the hose connected to the fuel rail using a flat-head screwdriver. Put the wood between the jack point and the tank.
Please refer their model a60 series manual. The failure mileage was 19,000. I can hear the fuel pump running and I am getting fuel to the fuel rail. The fuel pump had better not run with just the ignition switch turned on. Is this a good way of tying into the fuel line, where this guy instructs to tie into, in the video. The rest are caused by just the fuel delivery system, and it sounds like that's what we have. Is there a test port that I don't know about on the car that I can plug into? Ensure that the connector and resin tube do not contact, after installing tubes, make sure there is no fuel leakage, apply fuel pressure to fuel lines with turning ignition switch, start the engine and rev it up and check fuel leaks.
They had the exhaust manifold unhooked and the truck ran fine. Make sure they are not loose. The larger one is flex enough for the tank to be lowered. This new fuel pump module assembly is ideal for your restoration needs at an affordable price. Remove the Fuel Pump fuse located inside the car behind the coin-box-- use diagram on backside of coin box to find out which one it is 2. And becareful with RockAuto and the pulsar as they usually send the wrong part and I know this because I've experienced it already dealing with them. The other one is for the pump motor and should read perhaps one or two ohms.
Nissan has no type of screen or mesh in the converter to contain any pieces in case of a failure. All of a sudden I lost all power and the truck went dead. I was put in harms way for no reason. Section b , pages ec-423 thru 427. Is the factory regulator replaceable? I had both of the converters replaced and the problem was still there. Replace Fuel Pump 1997 Quest. Dealer states the door problem is due to a poor design with a heavy door on inadequate hinges.
Take out fuel pump and replace the o-ring with new one that is provided with your new fuel pump. Screw back the 6 bolts after making sure the O ring is in right place. Remove the fuel pressure gauge and the quick disconnect tool. The tank has been replaced and still does this. If so, how do you do it and what do you do it with? The manufacturer was notified and confirmed that there were no recalls and offered no other assistance. Disconnect the in and out lines by softly squeezing the line clips with a pair of smooth pliers and then pull the lines off the fuel pump.
Most mechanics use a test light so they can see it from inside when they turn on the ignition switch. The contact was driving approximately 65 mph when the vehicle stalled without warning. Replacement brand parts are the most affordable solution for all of your replacement needs! I was put in harms way for no reason. Jack the rear end of the fuel tank with a car jack and a piece of 2x4. If this had happened while I was passing the semi with another vehicle coming head on, this problem could have resulted in fatalities.
AutoZone's high-quality fuel pump replacement for Nissan Titan delivers just the right amount of fuel to your rig's motor so you always have the power to tow, accelerate and conquer hills. The contact stated that the fuel level gauge would display that there was one quarter tank of fuel when the fuel tank was actually empty. The dealer was contacted who stated that the fuel pump would need to be replaced. The computer in turn evaluates the gas pedal position which then sends a signal to the fuel injectors and throttle body to control the engine. Gasoline Fuel System 2004 Nissan Titan Gasoline Fuel System Consumer Complaints Complaint Number: 10609347 Incident Date: July 7, 2014 Date Added to File: July 9, 2014 Description of the Complaint: I was driving down the highway doing 75 in my 2004 titan. More than the level as shown full or almost full , drain fuel, from the fuel tank until the fuel gauge indicates level, q If the fuel pump does not operate, use following procedure, to drain the fuel specified level. The ignition switch can be off for this test.
But, when wired directly to the battery, the pump engages like it is supposed to do. Next, remove the fuel pump relay from that box and check for voltage on the terminals in the socket. The contact stated that the fuel sending unit failed and was causing inaccurate fuel level readings. Once the pressure build up it stops leaking that why I could never see the fuel leaking, until one morning I cranked up with the hood up. Leave the disconnect tool inside the end of the fuel supply hose. She also noticed that the vehicle was burning oil much faster than normal. Press the adapter into the fuel supply hose as far as it will go, then release the disconnect tool to lock it into place.
This time, since all the parts pictured were the same, I just ordered it. They too stated they had problems with the 04 fuel pumps. Usually there is a way to wrap a rubber band around it or wedge a piece of thin cardboard in it to keep it turned on. I have researched this topic online in forums and have found that this is a common problem with 2004 through 2007 nissan titans. The manufacturer was notified and confirmed that there were no recalls and offered no other assistance. The exact value isn't important now because there's going to be a few ohms of resistance in the meter leads. The dealership replaced the fuel tank and the fuel sending unit.
Assembly electrical connector and fuel feed hose, disconnect the quick connector follows, q Hold the sides of the connector, push in tabs pull out, several times until they start to move. However be very careful arou … nd the working area. For more information, go to. Please refer their model A60 series manual. After fixing the problem, I realized the truck should never have gone into limp mode.