If they Maximum load limit: 80 kg 176 lb must be stored, wrap them in appropriate cushion material. If neces- sary, adjust the brake light switch as follows. Few cool things are coming together for myself and Jon in may! Never open the throttle suddenly. Ride cau- tiously in unfamiliar areas. Place a container under the engine, and then remove the coolant drain bolt.
Place a container under the differential gear case to catch the oil. With the rear brake lever and pedal ap- Parking on a hill or other incline. Install the wheel and the nuts. Fuel expands when it by Yamaha because it may cause fuel system heats up. Pull outward on the areas shown, and then pull upward. When the needle reaches the ter.
A separate starter circuit supplies this mixture. Many expensive repair improve its general performance and extend bills have resulted from improper high the useful life of many components. Adjust the spring preload as follows. Install the bulb holder cover at the rear of the headlight. Do not touch the glass part of the bulb. See pages 8-6— flush the cooling system with clean tap 8-7 for panel removal and installation water.
Make sure to follow the Yamaha grizzly 700 on instagram! We have the helmets, goggles, and gloves covered too. Fully loosen the adjusting nut on the 0. Haynes writes every book based on a complete teardown of the vehicle. Could cause you to react more slowly. With a Haynes manual, you can do it yourself…from simple maintenance to basic repairs. Use the starter choke in reference to the figure: Position 1: Cold engine start- ambient temperature below 5 °C.
Be sure to keep your feet Could cause loss of control or a colli- firmly mounted on the footboards at all times. You should periodically remove and inspect the spark plug because heat and deposits will cause the spark plug to slowly break down and erode. Remove the battery and charge it. Dust or dirt in the gauge could cause the first reading to be incorrect. Rear shock absorber assembly 14.
Final gear oil drain bolt 7. It contains important safety information. To raise the beam, turn the adjusting screw in direction a. Book your next adventure now! Never go over the top of a hill at high speed. To prevent others might be likely to touch it. These are the slow blow variety. Insert the tailpipe into the muffler and align the bolt holes.
To install Place the panel in the original position, and then install the bolts. Anyone who has any experience of using wrong type of oil? Remove the tailpipe by pulling it out of the muffler. An improper fuse can cause damage to the electrical system which could lead to a fire. But gotta stay true to the Yamaha grizzly 700s! It is not acceptable proof of maintenance work. Use the electric starter to see if there is compression. Our equipment is well maintained and gassed up ready to go! Remove the bolts at the bottom of the fenders.
I just bought a Yamaha Big Bear 350 from 1992. Otherwise your feet may con- Removing hands from handlebars or tact the rear wheels. If any abnormality is noticed the following material. Put the tongue of sense and good judgment when carrying car- the loaded trailer on the scale with the go or towing a trailer. Install the new oil filter cartridge with an 10. Remove the front carrier by removing the carrier bolts. Have the spark plug tightened to the specified torque as soon as possible.
Most Improper cleaning of the spark arrester. Turn the adjusting nut on the brake pedal Brake pedal free play adjustment cable until the free play is 20—30 mm 1. Make sure to follow the yamaha grizzly 700 on instagram! Do not store the battery in an ex- cessively warm or cold place less than 0 °C 30 °F or more than 30 °C 90 °F. May is here and its time to see what the may mud has to offer the grizzly 700! In addition, the oil must be changed and the oil filter cartridge replaced at the inter- vals specified in the periodic maintenance and lubrication chart. They should Beginners should get training from a certified then regularly practice the skills learned instructor. This adjust- tion b to decrease the engine speed.
Do not exceed the specified differential 7. Remove the engine oil filler cap and wipe The engine oil level should be checked before off the dipstick with a clean rag. Gas tank to carburetor hook up, carburetor clean out of gum, etc. Install the oil filler bolt. Gonna be a pretty cool partner joining in with us pretty soon! Always follow the inspection and main-. Kind of Tough to do that with a paper manual.