Move the lever up or down cushion. Once retracted, the seat belt is in the emergency locking mode. It is important for simulating the conditions of the problem. G Reinstall bolt or screw securely. Take caution that keys, buckles or buttons do not scratch paint. Do not insert any object other than the same type male terminal into female terminal. Ground Inspection Ground connections are very important to the proper operation of electrical and electronic circuits.
Keep flammable material off the exhaust pipe and the three way catalyst. Box 191number: side Gardena, California 90248-0191For U. Headlight and turn signal switch P. Do not place cargo higher than the seatbacks. First check that the system is properly grounded.
In any powered circuit, an open can be found by methodically checking the system for the presence of voltage. When inspecting a ground connection follow these rules: G Remove the ground bolt or screw. Prices not applicable in Quebec. Do not smoke while working on the vehicle. G First aid treatment should be obtained immediately for open cuts and wounds. G Disconnect the battery negative cable. Use Folding the 2nd row bench seat you to fold the front passenger seatback flat of these areas by passengers could re- over the seat cushion.
G Wear protective clothing, including impervious gloves where practicable. Damage to the seal between wire and connector may result. After repairs, re-check that the problem has been completely eliminated. The retractor should lock and re- strict further belt movement. Doing so could impair active head restraint function. To probe each terminal, remove the connector retainer to make contact space for probing.
All diagnostic and repair procedures are covered. If the problem occurs inter- mittently, perhaps the problem is caused by corrosion. The open square shows current flow in, and the shaded square shows current flow out. Some child re- being operated. G Install only parts specified for a vehicle. Before checking voltage at connectors, check battery voltage. It includes much more interior space plus more efficiency features.
The shoulder belt may Infants 142. Type 1: Harness Wire Color And Connector Number Are Shown In Illustration G Letter designations next to test meter probe indicate harness wire color. To avoid or reduce the risk, the pro- recording or otherwise, without the prior writtencedures must be followed carefully. Before diagnosing a problem, familiarize yourself with each symbol. Little or no resistance will indicate that portion of the cir- cuit has good continuity. Unwanted resistance can be caused by many situations as follows: G Undersized wiring single strand example G Corrosion on switch contacts G Loose wire connections or splices.
Always sit well back in thechest. The meaning of are as follows: 3. G Replace oil seals, gaskets, packings, O-rings, locking washers, cotter pins, self-locking nuts, etc. G Do not apply excessive force when disconnecting a connector. Then pull up the center of each seat cushion, and fold on the recline lever and lean the seatback to each seat cushion toward the front of the a proper seating position. Always sit well back in the seat and adjust the seat belt properly.
The shoulder belt will not Manual front seat shownan accident or sudden stop. This can bechild could be seriously injured or killed in dangerous. Waterproof Connector Inspection If water enters the connector, it can short interior circuits. Torque member mounting bolt 13. The shoulder belt will not be against your body.
The seat belt may not fittion. Also, do not put the Failure to use a child restraint can re- same seat belt around both your child sult in serious injury or death. As an end result, it provides the outstanding off-road capability. These manuals are your number one source for repair and service information. In order to assure your safety and the efficient functioning of the vehicle, this manual should be read thoroughly. This may lead to intermittent problems. This would indicate a good circuit.
If possible, re-create the conditions present at the time of the incident. If the seal is missing, the waterproof performance may not meet specifications. Repeat step 1 and 2 again. Browse through our selection of Nissan repair manuals, which are equipped with all of the technical information and step-by-step guidance you need. The security indicator is located on the instrument panel. After accomplishing the Diagnostic Procedures and Electrical Components Inspection, make sure that all harness connectors are reconnected as they were. G If the battery terminals are disconnected, recorded memory of radio and each control unit is erased.