Pull back the rubber cover to access the old low beam headlight bulb. Test the new bulbs by turning on the parking lights, switching on the headlights, flashing the high beams and activating the hazard signals. It may help to use a screwdriver for parts of it, just be careful of the paint and bumper. The oil from your skin can cause the glass to shatter. Rotate them both toward the front … of the car, then pick themstraight up and the headlight will come out. The lower half of the air box is held in place by a few plastic pegs on the underside of the box that insert in to rubber grommets and act as friction fasteners.
Now that the bulb is free, pull the bulb from its holder and insert the new bulb make sure it clips in all the way. Not the most user friendly design either. Remove the engine air filter and set it aside in a safe place. When you need to replace the headlight, turning signal or parking light bulb on your 2008 Chevrolet Suburban, finding out what the replacement size you need can be a time consuming task. In some Chevrolets, the highbeam is the same bulb as the headlight and it is possible for the highbeam to work, but the headlight be burnt out even if they are the same bulb and vise versa. Re-insert the rear headlight bolt and tighten it in the clockwise direction with the 10mm socket and ratcheting wrench Push the black plastic bumper cover bracket in to place with the two pegs facing up towards the metal quarter panel.
Probably someone did not install it correctly. Put on the wing nuts and reconnect the harness. Replace the bulb ensuring to snap the bulb base connectors to the bulb holder. On the inside next to the tail light, there will be two plastic covers. On top of the headlight assemblies, there's a curved metal rod. Recently I replaced the bulbs in the headlights on my Mazda one finally burned out. You may need to use the needle nose pliers to remove the two pop rivets once they have been loosened.
If you try to pry the unit off, you will break the mounting tabs located in the forward portion of the tail light assembly. You just need to give it a little pull and the light will come out. Please help support this website by shopping at. Insert the screw on the bottom of the headlight assembly and replace the wheel well cover. Close the rubber flap to cover the low beam bulb and push in the pop rivet friction fastener with the loop that holds the two thin rubber hoses in place.
The light will then pull out of the truck. You may want to consider replacing both left and right at the… Open the hood. First, I'll show you how to replace either the Low Beam or High Beam bulb by removing the engine air filter box. Loosen the rear headlight bolt by turning it counter clockwise with the 10mm socket and ratcheting wrench. Paul Medeiros Open the tailgate.
Pull the old side marker bulb straight out of the socket and push in a new number bulb. Try to avoid touching the glass part of the new halogen bulb with your fingers or anything greasy in the engine bay. You should ha … ve the assembly free from the car. Replace the assembly as it was originally in. You should see thre … e plastic wing nuts and the harness connection to the tail light assembly.
The oil from your skin can cause the glass to shatter. The reason for that was because you have to put your hand up above the bumper support to reach the bulbs to pull out but you have to have a very skinny arm mine did not fit and after trying a couple of other guy … s I realized my son's arm and hand would fit and I told him what to do and he reached right up there and was able to take out the bad bulb and put in a new one. Learn how to perform this repair so you can be prepared when the issue arises. When you change the headlight on your Suburban 1500, it is important to not touch the glass part of the bulb with your fingers because the oil from your fingertips will cause that part of the bulb to burn hotter, which significantly shortens the life of the bulb. Take the screws out, and the tail light should swing out slightly and then pull straight back and out of the truck.
After replacing the bulb and screwing the housing back in place it seems to be perfectly secure. Use a clean glove or a paper towel. Pull back the plastic wheel well liner. The lower screw seems unnecessary. I had to replace a bulb a few weeks ago. At this point it is a good idea to close the doors if you have the 'barn door' style … rear doors.