Make sure the headlamp switch is in the off position, then remove the two screws and the license plate lamp assembly. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired. To operate the Trip Elapsed Drive Time perform the following: 1. If a puncture is located in the tire sidewall, stop and call roadside assistance. If equipped, remove the balance shaft.
These bolts must be installed in the same position 56. Remove the rear jackshaft plug. For example, a tire graded 150 would wear one and one-half 1 course as a tire graded 100. Bring vehicle to a complete stop. Each tap will increase the set speed by 1 mph 1. To release, press and hold the button 2 , pull the handle up slightly, then push the handle down. Turns the low beam headlamps Fog lamp control if equipped The fog lamps can be turned on when the ignition is in the on position, the headlamp control is in position and the high beams are not on.
You can check the tire pressure any time within the 120 miles 200 km by performing the procedure from Second stage: Checking tire pressure listed previously. Press and hold for a fast advance through radio frequencies or all loaded discs. This helps increase the effectiveness of the safety belts. They are a torque-to-yield design and cannot be reused. Remove the oil pump bolt and retainer and then remove the oil pump drive. Note: The interior lamps will turn off unless the dome lamp control is in the full-up position , and the turn signal lamps will flash if all doors, trunk and hood if equipped with active anti-theft system are closed and locked.
Install the new bulb in reverse order. Note: The temporary tire size for your vehicle may be different from this example. Your keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. Refer to Rear window defroster later in this section for more information. Trip elapsed drive time will only accumulate time when the ignition is in the on position.
Press and pull the window switch to open and close the windows. This unique guide, also known as the factory service manual is the one delivered by the manufacturer to the authorized dealer; and while many publishers may claim that their manual is capable of covering a single model for many years ahead, this however is not an honest statement. Power steering fluid reservoir 7. Ford Motor Company shall not be responsible for any such programming changes. Chilton's Ford Mustang repair manuals include diagrams, photos, and instructions you need to assist you in do-it-yourself Mustang repairs.
For high speed wiper operation, move control up three positions from off. These actions will severely reduce the life of the clutch and could nullify a clutch warranty claim. No risk Money Back Guarantee! Get one of our digital Ford Mustang Service Manual downloads and use the same information that shop mechanics working at Ford dealerships used to perform maintenance, warranty and repair work on these great cars. Access tether anchors located behind the seatback under the vinyl tag marked with the child tether anchor symbol. Temporary malfunctions may cause the Service engine soon indicator to illuminate. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions. Empty sealant bottles may be disposed of at home;.
To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out. Note: Ensure the brake pedal is not depressed during this sequence. Remove the bolt and the oil level indicator tube. Check seat covers and buckles before you place a child anywhere near them. Remove the air filter element from the air filter housing.
Department of Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it. While the lever is in the down position, tilt the steering column to its desired orientation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. Our products are licensed and approved by the Ford Motor Company. Stop the vehicle as soon as possible, switch off the engine and let cool.
Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. If equipped, remove the 2 bolts and the balance shaft chain guide. The compass is continuously re-calibrating due to changing magnetic fields and subtle, slow changes in vehicle magnetics which can occur over the life of the vehicle. To access this information, special equipment must be directly connected to the recording modules. Ask your technician to get the manuals in pdf format to be used on the go wherever required.