You can program up to eight transmitters. While the vehicle is operating via remote engine start, the vehicle's power window features will be disabled. Windows could even be open and the system would arm. To continue and program other remotes at the same time: open and close the driver's door and push lock or unlock on the remote. This was changed in 2003, models to a 'chirp'. Its a safety feature, but means you end up starting the car twice for no reason. The security indicator light on the dashboard will stop flashing while under remote engine start operation, but the vehicle is still protected.
In this event, perform the registration steps again beginning with part 3 above. The horn will honk 2 times when successful. The system does not open the trunk. The chirp is once for lock, two times for unlock, multiple times if a door is ajar when you try to lock them. Insert the key and turn it on and off twice, leaving the key in the ignition. Press the red button on the back and the horn will start flashing qucickly, repeatedly. It can't void the entire warranty right? The remote engine start system also has one programmable feature that can be adjusted to either make an audible horn chirp upon remote start activation or not.
Do this for all 8 digits. If the interval between one press of the switch and the next exceeds 5 seconds, an error will occur. If desired, you may turn the audible signal off. If an error occurs six times, perform the procedure again starting with part 3. If the code entered the second time is not identical to the code entered the first time, an error will occur.
I had one on my Tacoma and it was the best purchase I ever made for that truck. The antenna for the system is behind the glove box, so point the remotes in that general area and press the button on the remotes slowly and firmly a total of 5 times. The electronic tone will stop sounding when you start entering the number. Information here is subject to change, correction. If you don't have the remote put the key in the ignition and turn it on and off three times and the car will start on the 4th time 8. Dead battery After the battery is replaced, the transmitter must be synchronized with the keyless entry system.
Push the small button once to unlock the driver's door and disarm alarm, if set. If the interval between one push of the knob and the next exceeds five seconds, an error will occur. In the meantime, owners of vehicles involved in the recall with any questions or concerns may contact Subaru at 1-800-782-2783. The dome light goes on for 15 seconds and ignition key ring if present will light for 30 seconds when unlocked. An electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered. You ran out of gas, stop turning the damn key.
Take the key out of ignition the key has to be taken out. Remove one 1 slotted head screw securing the lower right side of the driver dashboard panel. Do not press the brake pedal. Press and release any button on the remote. Réinstallez le clip d'attache airbag au tableau A colonne et faites pivoter le panneau en place.
If you do not perform steps 1 and 2 within 45 seconds, an error will occur. Have a key but no remote? Sit in the driver's seat and shut all doors and rear gate. The keys must be replaced simultaneously if the body integrated unit is replaced. Several other people seem to have this same issue on various car forums. Use of the Subaru Outback wiring diagram is at your own risk. It might take a number of attempts to get into programming mode.
Horn will sound 2 times to indicate that the remote has been programed. In this event, perform the procedure again beginning with part 4. Can't imagine starting the car 20,000 times instead of 10,000 times is a good idea for the life of the car. In this event, perform the procedure again beginning with part 4. Also Benny, how is the range on your remote? Within 45 seconds do the following Open and close the driver's door once within 15 seconds and an electronic tone will sound for 30 seconds.
The botton is recessed in a plastic ring see diagram. Before the electronic tone stops sounding, press the lock side of the power door lock switch the same number of times as the leftmost digit of the transmitter code. Subaru Keyless Entry, Security Alarm, Immobilizer Key, Remote Start Systems. An electronic tone will not sound. The driver's door must be opened and closed between each remote you want to program. If the interval between one press of the switch and the next exceeds 5 seconds, an error will occur.
When a battery is replaced, the transmitter must be re-synchronized with the Keyless control unit. Perform the following steps within 45 seconds. Refer back to the 8 digit code. Yes, the dashboard instrument panel lights will flash when the parking lights flash. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote.