The dealer diagnosed that the brake fluid hose failed and needed to be replaced. Brake fluid of dollar rent a car was in between full and minimum. When the brake pedal was depressed, the brakes failed while the vehicle was in the park position. I went to my mechanic who advised me that Nissan has had trouble with the master cylinder. There may be an interior trunk trim panel that you have to take off but in most cases its just a series of thumb screws that hold them in.
This article has also been viewed 52,668 times. As a result, the contact's vehicle crashed into the rear of another vehicle. Test the new tail light bulbs by turning on the headlights, have someone step on the brake pedal and activate the hazard signals. The upper 10mm bolt is covered by a wire loom and power connector attached to it. It is really stuck in there but will give way. .
The brake pedal was applied but failed to stop the vehicle. He said my brake pads were fine. Pull the white plastic part of the wire harness straight off the threaded bolt end. The approximate failure mileage was 12,753. Use a pair of needle nose pliers and get the light out. Master cylinders did not provide proper pressure. This video shows you how to change the brake lights on your 2013 Nissan Versa.
Then gently pry out the two plastic access panels with the flathead screwdriver and set them aside in a safe place. We're here to help you find that perfect Brake Light Switch for your Nissan Versa. The air bags deployed and the brakes and steering wheel locked up. The brake pedal traveled to the floorboard. I called the dealer and left messages but no one is getting back to me. The black plastic brake light bulb socket is located closest to the outside edge of the vehicle.
Deaths will ensue if not dealt with this obvious defect. The manufacturer was not notified of the failure. Carefully push the tail light on to the rear of the vehicle. Turn the tail light assembly down on to the bumper. To avoid scratching the bumper or tail light, place a towel between them. If you insist on taking the housing out, take the nuts off the house from inside the trunk and pull hard.
The failure mileage was 23,000. Nissan Tilda outside North America is fairly simple, here's the guide to do it your self. Incident resembles no other vehichile experience I have had. It coasted to a stop. The approximate failure mileage was 31,000.
You should also see the clip at the sharp end of the light assembly and make sure to align it first when you put the light assembly back. The brake lights on your 2008 Nissan Versa illuminate when you hit the brake pedal and help prevent you from being rear ended by the cars behind you. I contacted ktnv channel 13 investigative news and they filmed me and my story. Entering your vehicle information in our Year Make Model selector up top, helps ensure you get an auto part that fits your car, truck or other type of vehicle. I never was able to get the wire harness off. The episode aired last night and today. This type of incident has happened a few times prior to this but not as severe.
Check your bulbs frequently and change burnt bulbs promptly. Here's a quick guide to changing the Taillight bulb on a 2006-2013 Nissan Versa Hatchback. Once I hit the wall the brakes came back on. Driving without a taillight assembly is a no no, especially since we've been hit with snowstorm after snowstorm. The contact had to place the vehicle in park in order to stop the vehicle from rolling.
When you replace the brake light bulb on your Versa, be careful not to touch the bulb directly with your fingers - the oil from your skin will cause the area that you touched to burn hotter than the rest of the bulb, which causes the bulb to burn out quicker. There are either 3 or 4 nuts holding the tail-light assembly in place, which means youll need to take out most of the inner panels to access the others. The vehicle was destroyed and towed. The approximate failure mileage was 93,000. You'll need a few handy tools and a bit of patience! Once both nuts are removed, proceed to the outside of the taillight assembly and gently insert a flat head screwdriver between the taillight and vehicles body, starting at the bottom of the Taillight. The manufacturer was made aware of the failure. I must bring this car in asap.
You should not need a sealant unless the rubber seal is done for or there is water inside the car. Nissan has holes in the body to access the tail light bulbs that may make the bulbs too difficult to remove without removing the whole tail light. The brake lights on your 2013 Nissan Versa illuminate when you hit the brake pedal and help prevent you from being rear ended by the cars behind you. Remove the screws and pull the bottom out and the top is held in by two retainers that should just slide right out Posted on Oct 13, 2009 I changed my wife's last night and there is no need to take the tail light housing out. For more, check out my other. I bought this one, and other than the one bolt I dropped down into some magical inaccessible space between razor sharp hunks of metal, I had zero problems with the install, and it only took about 20 minutes.