Im not too concerned with those options. The anchors can be a bit of pain, but if you place your hand between the seat bottom and back and then twist the piece at an angle, it makes removal a little easier. There are two tabs in the front of the seat cushion, one on either side in the front of the cushion by the carpeted area. If the fuel line can be removed very carefully it can be re-used with new hose clamps. Unhook the wires and bolt new one in. Hope it helps Time for Tea! My 98 the switch easaly pries out with a small blade, the article I read had you pop off the dash trim. Check with your dealer, before you take the car apart ;- There are two Hex screws at the top and one to the rear in the engine bay this one only need to be slackened since it is on a slide.
On the first gen Intrepids you have to remove the rear seat and then take off the shelf above the speakers. Remove that bolt using a socket wrench, or a basic wrench if you don't have one. Gen … tly pry off the side cover just above the wood trim. The fuel pump needs to be rotated counter-clockwise to the left to unlock it from the fuel tank basket. Now move the seat belts off the seat, so they wont be pulling against the cushion and place your hands on the bottom while kneeling towards the rear of the car. The arthritis Tools 17mm socket 10mm hex driver Ratchet Breaker bar Parts belt Tensioner Part selection For a replacement tensioner I recommend the Goodyear Gatorback tensioner 49267. Whether your old one is torn or shoddy.
Than ask your partner to stay there. Hidden screws, hard-to-remove plastic anchors, and the need for specialty tools means that this job could be a real nightmare. You're done All in all the procedure is pretty simple. If you dont have one, then you culd try this. You simply need to push these towards the rear of the car and the cushion will release.
There is also pictures that i attached of a small partthat is missing from the passenger sidepillar if that is the correct term to use for it. Disconnect the electrical connections and move them aside. A bad battery can put a. After an about 1 hour and after what you finish your last beer go to see you partner and tell her that you are done. Dont worry about it being heavy, its only about 5 lbs max. Looking through the records the previous owner did not have the filterfluid changed by his dealer.
Attach the wires alongside the fuel line with the zip-tie and cut the end of zip-tie off. Replacing the speakers is a reversal of these instructions. I am guessing to get an A4 Avant 2. The wipers did work and the 30A fuse was good so decided it was the washer pump. I don't have any pics to post unfortunately.
The key is to push the round side opposite of the flat side inward and pull up on the chassis fuel line. This has been tested on a 1995mod A4. The seat looks great as I mentioned in the What Did You Do. Screw em back in and presto. Note that the little raised metal bumps on the side of the bulb base mean it only goes in one way before giving a little twist to lock it in place.
Is there a way to unlock them or do I have to buy a new system Been driving the car for 3 months with no belts its about time I fix it. Pull off the clip on cover, remove the cold air scoop and look round the air box until you locate a series of metal clips. I took it into the audi dealership and they said it would be 150-200 for the seat belt and since they would have to remove the whole seat to put a new seat belt and buckle in labor would be 200. It seams like we get the same exact questions all the time. It takes a little pull up on the fronts by the holders. If you have a 2001 A4 Avant, you can access the bulbs from inside the rear Cd changer and road jack compartments, using only a screw driver. If you're a true automotive enthusiast and of.
These are the bracket that are in the front of the bottom cushion. Use paper towels to soak up the excess Brake Clean and dirt. The terminal connectors have two tabs that will be crimped on-top of the wire. You have to first pull out towards the front of the car, to get the brackets off the bolts, then lift up swiftly and strongly to lift the top brackets out of the grooves. To the right is a picture of the stock fuel pump right next to the new high-output fuel pump with hardware kit left.
I am going to remove the covers underneath to remove the wires. Look at the very tip, and about 2 inches down there should be a crack. Within that time go to the Halfords Buy a bulb and ask them to fix it for you. Come back during the day your partner would not see that lights are already working. Then use a screwdriver to bend the upper corners outwards while pulling the bumper forwards. Re-assembly is the reverse process above: don't forget to make sure the sealing rubber is correctly seated in the bulb holder before you click it back together again. When the conditions get bad I park my other car and drive the audi.