Is there continuity and is the resistance within the specified range? Reverse procedure to install and prior to installing new sensor, lubricate sensor O-ring. Refer to in Wiring Systems. The system attempts synchronization and looks for an increase in engine speed indicating the engine started. When your Pontiac G6 was born, it was destined for a driver who prioritizes trustworthy transportation in their automobile. As the camshaft rotates, the reluctor wheel interrupts a magnetic field produced by a magnet within the sensor. Refer to in Wiring Systems.
Refer to in Wiring Systems. Did you find the condition? Procuring new Pontiac parts from www. It is located under the water pump. Refer to in Wiring Systems. Sometimes they come loose and cause a no start or long crank. Their sturdy design ensures durability and long-time service.
The seventh slot is spaced 10 degrees after one of the 60 degree slots. Parts cannot be returned after they have been installed. Is the voltage less than the specified value? Refer to in Wiring Systems. Achieving optimum fuel efficiency and power output nowadays depends on the precision at which your engine's internal sensors are functioning. The sync pulse is used to synchronize the coil firing sequence with the crankshaft position.
Year Make Model Description 2010-2013 Buick LaCrosse Buick LaCrosse Camshaft Position Sensor L4 2. Refer to in Wiring Systems. The things this company has to differentiate itself. Did you find and correct the condition? Contact us with any questions before installing the parts. Here at Advance Auto Parts, we work with only top reliable Camshaft Position Sensor Connector product and part brands so you can shop with complete confidence. Pontiac G6 Camshaft Position Sensor parts for 2010, 2009, 2008, 2007, 2006, 2005 vehicles are available here. Refer to in Wiring Systems.
Does the test Lamp illuminate? The reluctor wheel is inside the engine immediately in front of the rear cam bearing. Refer to in Wiring Systems. Refer to in Wiring Systems. While it's not hard to buy replacement parts for Pontiac vehicles, these days only the absolute best are required to fix your automobile. If you car's engine is 4 cyl you have 2 O2 sensors and if you car's engine is 6 cyl then you have 4 O2 sensors for each bank, 2 for left bank and 2 for right bank. This information is then used to determine the optimum ignition and injection points of the engine.
With the camshaft cover removed and the 1 cylinder at top dead center, make sure that the darkened chain links are lined up with the alignment marks on the exhaust and intake cam sprockets. All Replacement brand items are backed by 1-year, unlimited-mileage warranty. Refer to in Wiring Systems. AutoTrust Platinum provides a growing selection of low-priced cams, timing, and valvetrain parts. Refer to in Wiring Systems. Refer to in Wiring Systems. Each notch, or feature of the reluctor wheel is of a different size for individual cylinder identification.
The numbers below refer to the step numbers on the diagnostic table. Did you find and correct the condition? Bring your G6 back to life with the highest quality replacement parts from the experts at Car Parts Discount. Do you know what the five volt reference circuit is. Does the scan tool parameter increment? Don't go too long without fixing your Camshaft Position Sensor. Does the scan tool indicate that this diagnostic failed this ignition? Did you find and correct the condition? Did you find and correct the condition? Inspect the jumper harness for poor connections. A bad or malfunctioning cam sensor will often cause a service engine light error code, and or cause a no start condition, or rough running due to inaccurate ignition and fuel timing. Observe that as long as the Crankshaft Position sensor 24X signal is available, the engine will start.
Keeping your G6 in top shape is your top priority. Did you find and correct the condition? A slightly longer cranking time may be a symptom of this condition. . Refer to in Wiring Systems. Refer to in Wiring Systems. Is there continuity and is the resistance within the specified range? Refer to in Wiring Systems. Did you find and correct the condition? This relationship is used to determine camshaft actuator position and control its phasing at the correct value.