Plug the new replacement bulb into the wire harness without touching the glass of the bulb. Use torque wrench and tighten bolts using star method as indicated in service manual or ask anyone who's worked on engines to show you. Wrong answer, I could have saved some time by reading my manual before I went shopping. The only way I can see to do this is to: remove the door card insert a long bar through the door and attack it with a big hammer until it all falls apart! Difficulty:Moderately EasyInstructions Locate the headlight socket. Value and reliability coupled with style are benefits of driving your Nissan Sentra. With the right replacement bulb in hand, fixing one of these broken lights is quick and relatively easy to do. Locate the four fascia retaining pins and remove them using the flathead screwdriver.
Once you flip it up you will notice it has two places where it holds the bulb in, one on each side. How to Replace a Headlight in a Nissan Xterra Open the hood to the Xterra. At the top of of the assembly you'll see two metal posts poking through white nylon fittings. The light should now function properly. Before installing a light bulb into the socket, ensure that all electrical contact surfaces are free of corrosion or dirt. Turn the bulb counterclockwise to remove from the assembly.
This coating is a modern reinvention of their Arctic White color which made them famous. Once the bulb is in place, put the copper clip back in place, noting that you should put the small flat piece under the flange where the collar wire will screw back in first. Line up the replacement headlight bulb with the socket. You have to remove the wire holder, and then you can pull out the bulb in its holder. This one is a real pain to get off. I hope that all I have to do is remove the plastic bottom to gain access to the bulb. I am assuming normally you wouldremove the headlight assembly which would cause you having toremove the grill and a couple other things, but since this israther hard and I'm lazy i just decided to try and … reach.
This pair of Aftermarket Nissan Sentra Head Lamp bulbs is from Nokya's Cosmic White series. For the passenger side, remove the battery bolt with the ratchet, extension and a socket. Remove the headlight socket by turning it counterclockwise and pull The 2003 Nissan Altima comes equipped with xenon hight-intensity headlight bulbs for the high beams and halogen bulbs for the low beams. This pair of Nissan Sentra aftermarket Head Light Bulbs is from Nokya's Arctic Yellow Bulb Line. New bulb goes in clockwise to lock.
I suggest that you see how the bulb goes in so it aligns correctly. Everything else is clips, and should pop right out. Replace the cap so nothing falls in. Also, unhook the gray harness under the light, before removing. Use a tissue or something else in that order to handle the new bulb. Pull the bulb from the socket.
There is a locking clip that you depress with your thumb to unlock the connection to the bulb casing. Now the bulb is secure and does not wiggle. First push it down towards the ground , then push it to the left as viewed from the outside-front of the car. First push it down towards the front of the car , then push it to the left toward the passenger side. Now comes the hard part.
Driver Side: 1 Remove the 10 mm bolt that holds the air box down this is on the gold colored bracket on the driver-side fender. Once you get all the junk out of the way the air box on the driver's side and the radiator overflow on the passenger side you will see a 10 mm bolt right in the middle of the headlight assembly. Should you be unlucky enough to have the headlamp bulb in your Nissan Sentra burn out, you can replace it yourself. It's actually just as easy to take the whole light out. It's not like the old days when the sealed beam units were replaced. Insert the new bulb, and then twist the ring back on the retainer.
For all, it recommends at least removing the negative battery cable. For now I performed by-pass surgery - hooked the low beam from the left to the right and now it works fine. If you need to change a bulb on your headlight, you can reach in the back. Once removed, you'll have to take out all the head bolts. These little tabs are locked in, so when you look back there, you just want to push those tabs back and then press there to disconnect. You may want to consider replacing both left and right at the same time… Open the rear hatch - remove the screws that are exposed that hold the lens housing to the sheet metal, and carefully remove the lens housing from the body metal.