Note: The following programming step may take between 10—12 min. Be sure to follow the exact sequence of the Service Fast Learn procedure as outlined in the appropriate Service Information. Refer to Battery Tray Replacement. Other materials: Warning: Refer to Glass and Sheet Metal Handling Warning. If the control module is not properly configured with the correct calibration software, the control module will not control all of the vehicle features properly. Refer to Immobilizer System Component Programming. Camshaft Actuator System Overview 1 Camshaft Actuator Vane 2 Timing Chain Sprocket 3 Engine Oil Pressure-For retarding the camshaft 4 Camshaft 5 Input Signals from Engine Sen.
Do not connect a battery charger. To help avoid damage to vehicle control modules, do not turn off the ignition during reprogramming unless instructed to do so. The data tree includes the original characterization data so that it can be updated with the new component information. Refer to Front Opening Upper Cover Replacement. Performing the steps out of order or not completing all steps may cause the programming to be unsuccessful or cause features to work improperly. If a communication error develops while transmitting to the vehicle, there is a risk of damage to the vehicle module that may be unrecoverable. Front Floor Console Replacement Callout Component Name Preliminary Procedures Remove the right and left front floor console extensions.
If an interruption occurs during the programming procedure, programming failure or control module damage may occur. Note: The Prepare Control Module for Removal function can only be performed when communication with the old control module is still possible. . The main function of this tool is to act as a clean power supply during re-programming to avoid module failures. Review the Control Module References in the Service Information for module-specific programming and related procedures. The control module should program.
If there is an interruption during programming, programming failure or control module damage may occur. Refer to Immobilizer System Component Programming. This is legit online company. Any fluctuation, spiking, over voltage or loss of voltage will interrupt programming. Removal Procedure Remove the battery tray. Programming a control module at any other time will not permanently correct a customer concern.
I just happened to stumble on to them. Disable or adjust the Windows® Power Options to prevent the computer from going to sleep during the programming event. If a cable is suspect, substitute another cable. Refer to Front Floor Console Extension Replacement - Right Side and Front Floor Conso. Repair Instructions Perform the Diagnostic Repair Verification after completing the repair. Electrical Procedures Following is a list of electrical procedures that are associated with reprogramming or control module replacement. Remove all mounds or loose pieces of urethane adhesive from the pinchweld area.
These numbers can be difficult to access when the components are installed on the vehicle. It is with 30 languages available to choose,and support with wifi,but now you need to buy wifi card or you have the wireless card yourself. Failure to perform all programming actions at the same time on a vehicle may result in additional drivability concerns. The internal breaker protects against reverse battery polarity, brownout, over-temperature and over-current situations for a long and trouble-free tool life. This is a normal security timer response and a restart should not be performed. The main function of this tool is to act as a clean power supply during re-programming to avoid module failures.
They were the only company who offered the part I was looking for to repair a tool. After successfully programming the control module, ensure that all post programming procedures are performed; refer to for the appropriate control module Programming and Setup document for any required procedures. Stable battery voltage is critical during programming. If there is an interruption during programming, programming failure or control module damage may occur. Beware that cables are still prone to physical damage, such as deterioration of the cable or connector, which is not always visually evident. The Immobilizer Learn procedure needs to be performed again.
In these cases even a fully charged battery is not sufficient to maintain system voltage during a sequential event. Solenoid Valve Characterization Reprogramming The solenoids in some transmissions require unique performance characteristic data in order to function at maximum efficiency. Reliability takes precedence over convenience, so keep it simple. Pull the cable retainers 2 to release the shift le. A power supply should be used at all times. This method is simple, easy and eliminates any potential for a network problem to interfere while transmitting data to the module during programming.
If the original window is being reused, remove all but approxi. Other materials: Front Bumper Fascia Replacement Callout Component Name Preliminary Procedures Remove the radiator opening upper cover. Remove the front bumper opening lower cover. In these cases even a fully charged battery is not sufficient to maintain system voltage during a sequential event. Review the information below to ensure proper programming protocol. I have no complaints what so ever. Any fluctuation, spiking, over voltage or loss of voltage will interrupt programming.
When Immobilizer Learn is complete, press the Unlock button on the keyless entry transmitter to allow the keyless entry transmitter to exit the Immobilizer Learn mode. Based on the control module being programmed, some vehicle modules will require configuration, reset or learn functions to be performed after programming. Any fluctuation, spiking, over voltage or loss of voltage will interrupt programming. Disconnect the shift lever and selector lever cable end 1 from the transmission shift lever and selector lever. If an error or connection problem occurs during file retrieval, it may be necessary to restart or recover and carry on retrieving the required files. Check the Service Information Every Time The Service Information should always be reviewed for the appropriate programming and set-up procedures of an individual module. I will be shopping here for now on and would highly recommended them to anyone.