This ensures a good seal for the new gasket. Using a Phillips 2 screwdriver, turn the adjuster either clockwise to adjust down or counterclockwise to adjust up. On the wall or screen you will observe an area of high intensity light. Posted on Jun 26, 2010 Apr 10, 2012 - Uploaded by GregHint See how even a novice can repair a passenger mirror on a FordEscape. The more local you shop, the more you save off the shipping cost. Some Fords have high intensity discharge headlights, sometimes referred to as xenon lights.
Correct Item Guaranteed If you receive an incorrect item from us, we will immediately pay for return shipment and send you the correct item. Tools required: Turn Signal - none, Low Beam - flathead screwdriver or panel tool, High Beam - socket set and wrench. To access the passenger side headlight bulb, remove the washer fluid fill hose by removing the single 7mm bolt. We do not require a core charge or a return of the old part or engine. Claims on engine warranties are limited to manufacturer defects in the pistons, heads, block, crankshafts, rockers, and oil pumps. What I can say about you, Eric, and the Go-Parts.
For example, if you need to replace the passenger low beam bulb, turn the steering wheel all the way to the left. This may sound hit and miss but even the manufacturers change things like this within model years. Thanks for all your kindness! If your Fusion has this type of bulb, we do not recommend that you attempt to change it yourself. Locate the vertical adjuster on each headlamp. These bulbs have a very high voltage that runs through them, even if the battery is disconnected. Now that you have more room to work with the wheel turned out of the way, you can remove the black plastic wheel well liner fasteners.
Try not to score the metal when cleaning. To access the driver side high beam bulb requires removing the air box. Item in Good Condition Guaranteed If the part we ship to you arrives in damaged or non-working condition, we will ship another item out to you immediately. Re-install the wheel well liner fasteners by first inserting the larger outer piece and then push the smaller inner piece in place. Be careful though not to damage the hose. Take the bolts completely out and remove the housing from the engine block. Easy Returns Guaranteed We offer a no-questions 100% money back guarantee on all items returned within 60 days of delivery.
By ensuring we follow manufacturer advertising guidelines, AutoPartsWarehouse. Start vehicle and let it run for a little bit to check for leaks. There should be 2 bolts on top off the housing. Donations are not tax deductible. The easiest way to access the Low Beam headlight bulb located at the outer edge of the assembly, is by going through the wheel well liner. The Turn Signal light bulb is located at the inner corner of the headlight assembly closest to the center line of the vehicle.
The horizontal edge of the brighter light should touch the horizontal reference line. Changing both headlight bulbs on your Fusion at the same time will allow both bulbs to have the same intensity and prevent the new headlight bulb from appearing brighter than the bulb on the opposite side. The top of the high intensity area should touch the horizontal reference line, if not, the beam will need to be adjusted using the next step. The original auto part must be returned using the provided shipping label. Close the hood and turn off the lamps. Terms: All returns and cancellations may be subject to shipping charges, unless caused by our error or cancelled by the customer prior to shipping.
Sometimes it's easier to use a screwdriver to pry the hose off. Common items that are not guaranteed include but not limited too nuts, bolts, links, seals, bushings, ball joints, brackets, bezels, wiring, cables, sensors and other applicable items depending on the part. Hope the picture is right - you'll see an european Miata with american rear lights ;-. The fasteners can be removed with a flathead screwdriver by prying out the small center portion and then popping the larger outer part of the fastener with your fingers or a panel tool. Use a flathead screwdriver to disconnect the power connector from the base of the bulb. All of our engines and transmissions carry a 1-year warranty with optional extensions up to 2 additional years.
If everything checks out, you are good to go. Test the new bulb s by turning on the headlights, activating the hazard lights and flashing the high beams. Replacement headlight bulbs for the '06-'12 Fusion with their respective part numbers are as follows: Low Beam , High Beam , and Turn Signal. . Replacements: It is company policy that we receive the original auto part back before sending you a replacement auto part. Note all returns and cancellations require a prior authorization. In some Fords, the highbeam is the same bulb as the headlight and it is possible for the highbeam to work, but the headlight be burnt out even if they are the same bulb and vise versa.
Disclaimer: -Some of our units used engine, transmission, axle, etc. If they are not serviceable, such as a pressed-in ball joint, they will be guaranteed. Citations can be issued for products that do not meet the minimum regulatory requirements. If you found this guide to be helpful, please consider making a small donation by clicking on the PayPal. Whenever I called for assistance, I always found an open ear and good ideas to keep things going on. If not, don't buy it.
It typically takes us approximately 3-5 business days to process a credit back to your account and 2-3 business days for the credit to appear on your account. Sometimes it helps to have a razor blade or other scraper to clean it with. Follow the upper radiator hose from the radiator to the engine block and there you should see a neck where the hose is connected to the engine block. For more, please check out my page. To see a clearer light pattern for adjusting, you may want to block the light from one headlamp while adjusting the other. Best Price Guaranteed Our prices are hands-down some of the lowest you'll find on the net. Replace the rubber dust cap by pushing it into place.