Fiber Guide Pins Fiber Holder. Other Necessary Items for Splicing Operation Fiber coating 0. Straps for small accessories may be recommended. An environmental performance decreases when the protector is detached. Dropping Water-Proof Dust Fujikura does not guarantee that the splicer will not be damaged under these conditions. In addition, it can program an independent power saving setting. This option can be recommended when fiber has some memory curl, so operator can make sure the fiber is surely clamped before wind-protector is closed.
Visual inspection with the monitor is often necessary for better splicing yield. Enter key Menu key 3-3. Cleaning optical fiber Clean optical fiber with alcohol-impregnated gauze or lint-free tissue approximately 100mm from the tip. Attenuation splice mode Attenuation splice mode makes an intentional core axial offset to create attenuation at the splice point. The following warning screen is displayed. With over 40 years experience in splicer service, Fujikura customers can be assured only the best quality service is provided.
A set of splicing parameters is selected for the identified fiber type and the fibers are automatically spliced. Arc Calibration Atmospheric conditions such as temperature, humidity, and pressure are constantly changing, which creates variability in the arc temperature. Each tube-heating mode is optimized for a type of Fujikura protection sleeve. Contact Address Inquiries concerning products should be made to the distributor or one of the following: Fujikura Europe Ltd. Cutting lever Stopper 2 Push the slide button until it locks. Every Fujikura distributor has a service center and professionally trained personnel who are able to address the concerns of each customer quickly and effectively. Motor Calibration Motors were adjusted at the factory before shipping.
It is small in size and light in weight, making it suitable for any operating environment. Select a mode Sleeve type in the list and this is copied to a user-programmable mode. The following procedure is required, and is different from standard automatic splicing. Through these courses, you will gain an understanding in fiber optic communications, installations, testing procedure and equipment. List of Splice Results Splicing results stored in the memory can be displayed. Pull and unlock wind protector mirror latch with fingers.
Referring or editing splice mode Splicing parameters in each splice mode can be Select Splice Mode Menu modified. This function automatically calibrates the speed of all six motors. Adhere to all safety instructions and warnings contained in this manual. Such abnormally high voltage or frequency from a generator may cause fuming, electric shock or equipment damage and may result in personal injury, death or fire. The splicer average splicing loss 0. Keep this manual in a safe place.
Coating diameter: 100 to 1000µm Fiber setting and cleaved length Sheathe clamp A standard : For coating dia. Detached from carrying case Splicer and equipment fixed to tray. Available Intentional high splice loss of 0. With more than 80 authorized distributors worldwide, customers can rest assured that their concerns will be responded immediately by their local Fujikura distributor. This may result in electric shock, splicer malfunction or poor splicing performance. Cleaning Fiber Clamp Chips Cotton swab If contaminants are present on the clamp chips, proper clamping may not occur, resulting in poor quality splices.
Copy the appropriate one and paste it to the user-programmable area. Tightening the original screw without the protector may damage mechanism inside. Do not attempt to use this machine for other applications. Failure to follow the above instructions may cause abnormal arc discharge. Fiber holder System 1 Set the fiber onto the fiber holder with the fiber protruding 30 to 40mm from the end of the fiber holder and then close the fiber holder lid. Single Cladding diameter : 80 to 150μm. Clean the lens or Fiber objective lens or the the mirror if dust or dirt exists.
Below are the descriptions of the various parameters used in these modes. For this reason, Fujikura Ltd. Battery operation Check and make sure the remaining battery capacity is 20% or greater before operation otherwise few splices can be made. However, surface tension created during arc discharge aligns the fibers cladding-to-cladding due to the viscous self-centering effect. Press Escape key to exit. Using the electrodes without a replacement will result in greater splice loss and reduced splice strength.
However, settings could change due to various reasons. Electrodes should be stabilized to reform the arc discharge. Splice mode selection Select an appropriate splice mode for type of fiber to be spliced. Manual Splice Mode This mode is to manually align and splice fibers. Replace Wind Protector Mirrors Replace the wind protector mirror if it cannot be cleaned or if it remains clouded.
Selecting Heater mode Select the heater mode most suitable for the protection sleeve to be used. The again to seat it correctly at the bottom of the Forward fiber position is out of V-groove. The fiber image data is displayed. The equipment is placed in a 1 cubic foot box with total 6 teaspoons of dry 0. When the number of splices exceeds 2,000, the caution message changes to the warning message.