April 6, 2013 Followup from the Pelican Staff: Usually the sensors are on the left front and right rear of your vehicle. Use a 27mm socket to loosen and remove the oil filter housing cover See. Part of your oil filter kit should include a large O-ring. Order now and change your oil less frequently. Most drivers will enjoy a an oil change that will last for a year when switching to Amsoil! I just bought my daughter an 02 R53. We disclaim all warranties of any kind. October 27, 2014 Followup from the Pelican Staff: The filter may have a defect, causing it to collapse.
Their high flow design can help to improve engine performance by reducing oil filter restriction. Hop out of the car and look at the engine compartment, then take a quick look underneath the car. The engine was blown so I found a good low mile used one. Start the cannister cover by hand to avoid cross-threading. Is it available separately without replacing the filter cover? Take care to make sure the threads are lined up and it seats correctly.
It's also good to keep an extra quart in case you need to top off your oil. May 6, 2017 Followup from the Pelican Staff: You can remove the spring and cage. The only areas I accessed were the drain plug and filter housing. It leaves me wondering whether this housing was changed or not. October 7, 2015 Followup from the Pelican Staff: I prefer draining from the oil pan. I cannot find it referenced or even pictured in any part manual. You will spill less oil this way.
August 8, 2018 Followup from the Pelican Staff: The filter housing can be tough to get out, especially on R52 models. I need to find the filter that fits the old style housing. Contact your local shop in your area and ask if you can bring your own oil. It twists to lock into place. November 23, 2015 Followup from the Pelican Staff: Thanks for the tip. This should be facing down when you install the filter.
It may have been overfilled. It offers superior performance over conventional motor oils. After the warranty ran out, considering how the many miles I've driven it; I've been doing what any maintenance I could on it on my own. June 7, 2014 Followup from the Pelican Staff: It should as the drain plug is located at the rear of the oil pan. Should this core and the spring be removed from the housing now that the new filters come with a plastic core in them? Its a big job for just replacing gaskets instead of entire housing. Thanks again, Alan August 21, 2013 Followup from the Pelican Staff: Thanks for the feedback. I would suggest replacing it if it came out.
Changed my motor oil and filter about 3 months ago and the car was making a noise while cold. The stock drain plug can be reused a few times but it is a good idea to replace it every few oil changes because the threads get worn, the head can take abuse and get stripped out and as it tightened the threads can stretch a bit which in extreme cases can allow oil to leak. It meets a wide variety of specs and approved by various manufacturers. When my husband went to change the oil a spring fell out and we didn't realize there was a cage in the filter so it was thrown away. They have awesome pricing on aftermarket Mini items and mods, and you simply cannot beat the customer service!!! Figure 2 Start out by letting the car warm up. This should be facing down when you install the filter. Give our parts specialists a call, they will help you find the right drain plug.
August 8, 2014 Followup from the Pelican Staff: No problem. I asked the salesman if there was a way to reset the oil light. Anecdotal evidence suggests Turbo's with more frequent oil changes have fewer issues. See and There will be no time to grab any more buckets or oil pans if you underestimate, so make sure that the one you choose is big enough. The car will perform a dash light check. Im afraid that I could strip the threads.
This will be a bit difficult due to the location of the housing, but a few wadded paper towels should do the trick. The tag on the engine clearly says 5w 30 recommended but you used 0w 50. The oil drain plug located on the bottom of the engine's oil pan. Continue to add about a half a quart at a time and keep checking the dipstick. Start the cannister cover by hand to avoid cross-threading. I am planning to change my own oil. The rubber seal on the top of the filter should be facing down when you install the filter.
February 1, 2017 Followup from the Pelican Staff: Give The Pelican Parts parts specialists a call at 1-888-280-7799. In warmer climates, you should use a 20W-50 oil. On the last install of the new oil filter I found a spare part that I did not recognize laying on the ground just as I was cleaning up. If the crush washer has slot on one side? Thankyou for your time an any help you can provide. It's a tight fit to get the socket on there. This article applies to the.
It is definitely an easy and straight forward process, usually. Once confirmed it is good, look at the sensor and wiring. January 12, 2013 Followup from the Pelican Staff: Normally they are equipped with oil drain plugs. Take the cover and screw it back down over the new filter cartridge. February 24, 2015 Followup from the Pelican Staff: I think you need a filter cover. Give our parts specialists a call at 1-888-280-7799. I find it easier to do.