Entering your vehicle information in our Year Make Model selector up top, helps ensure you get an auto part that fits your car, truck or other type of vehicle. Just make sure that you completely remove any corrosion and that the socket is dry before you reattach the bulb. As a result, water can seep through the cracks and stay inside the assemblies, causing the bulb socket to corrode and the lenses to get oxidized. We're here to help you find that perfect Tail Light for your Nissan Versa. Slowly pry very slightly under the Taillight until it starts to move away from the body. Start at the bottom then the middle of the Taillight.
But before you sand your assemblies, don't forget to cover the areas along their edges with a tape to avoid damaging the paint. Remove the screws and pull the bottom out and the top is held in by two retainers that should just slide right out Posted on Oct 13, 2009 I changed my wife's last night and there is no need to take the tail light housing out. Dilute a mild dishwashing soap in warm water. Usual Problems of Your Nissan Titan Tail Light Assembly Your Nissan Titan tail light assembly may fail to work anytime-sometimes even without your knowledge-and may experience a corroded socket, an unlit bulb, or a leaking assembly. And once applied, use a non-abrasive cloth or towel to buff your lenses. But what's important is that you know what to do should you experience any of the tail light assembly problem.
Needless to say the shipping and delivery were as promised and I had my daughters car up to standards for Texas within two weeks. To help prepare you, here are some troubleshooting tips: Unlit bulbs You may be wondering why your tail light assemblies sometimes have problems lighting up. Checking the fuse and fixing any bad wiring on your pickup should make both of your tail light assemblies work. You'll need a few handy tools and a bit of patience! You can use 1500-grit sandpaper to scrub your tail light assemblies. I have taken it off before but you do not need to access the light.
Backed by 1-year, unlimited-mileage warranty -- Replacement brand parts are the most affordable solution for your replacement needs! Corroded bulb sockets Another problem you may encounter is a corroded bulb socket that greatly affects the function of your tail lights. After spending several hours on different web sites I found Go-Parts. You can buy any good-quality polishing compound from any auto supply store. Now, this is a high-risk problem as your truck may not be seen at night by other drivers, which can cause a road accident. But make sure that the water isn't too hot as this may affect the surface of the lens.
That's why it's important for you to know these useful tips to help you properly maintain your assemblies: Cleaning tips Wash the assemblies. Here's a quick guide to changing the Taillight bulb on a 2006-2013 Nissan Versa Hatchback. This article has also been viewed 52,640 times. You can choose to clean the corroded socket using a dry brush or abrasive pad. I order several parts for a Chevy Geo that my daughter and her husband owned. In this case, you may need to first check the bulbs inside your assemblies because chances are they've just already blown.
Also, read the instructions at the back before using it. To create this article, volunteer authors worked to edit and improve it over time. However, you must keep in mind that you only do this if just either one of the two tail lights fails to work. If you're successful, you may never have water droplets inside. The corrosion that has developed on the sockets can stop the bulb from working and may even damage the bulb or the wire. In this way, you're protecting your lenses and sockets from getting damaged by water. Other maintenance tips If you find tiny water droplets inside your tail light assemblies, you may want to check their seal for any crack as this only happens when water manages to get inside.
There may be an interior trunk trim panel that you have to take off but in most cases its just a series of thumb screws that hold them in. Nothing beats a clean and shiny Nissan Titan tail light assembly to complement the overall look of your pickup. We have worked hard to design a site that caters to everyones Nissan Versa Tail Light needs. If you want to make your tail light assemblies looking as shiny as new, you need to polish them. Use a pair of needle nose pliers and get the light out.
There are either 3 or 4 nuts holding the tail-light assembly in place, which means youll need to take out most of the inner panels to access the others. Remove the nuts and screws, then remove the taillight. Disconnect the connectors from the taillights taillight bulb connectors are visible by looking inside the trunk at the back of the tail lamps. . Should both of them malfunction, your truck may be dealing with a blown fuse or an electrical problem with the wiring. You also need to prepare a bottle spray filled with soapy water for wet sanding. You should not need a sealant unless the rubber seal is done for or there is water inside the car.
Keep in mind that warm water should soften any hardened dirt, so you should be able to remove buildups on the surface of your assemblies. Keep in mind that you have to regularly spray the mixture on the surface to avoid getting it scratched. Water-filled assemblies The seals on your tail light assemblies can be damaged overtime. However, you just have to simply replace it to have a working tail light assembly again should the corrosion be severe. It is really stuck in there but will give way. Also, make sure that you sand in a side-to-side direction, not in circles, and with gentle pressure only. Besides cleaning your assemblies, you can prevent oxidation by applying silicone along the open areas on the seals of your assemblies to protect the interior.
We love when auto parts experts come to our site and we love when car parts newbies come to our site. To prevent water from getting trapped inside, which eventually will cause further problems, you need to cover the cracks on the seals with silicone. Just make sure that it's well trusted by many drivers to avoid any problem. You may see only one assembly giving a red glow or notice that both of them fail to light up. They had drove the car from Michigan and there were parts that were needed to get them up and running in good shape.