This will give you access to the bulb holder. I and a bunch of my friends had same problem. On the passenger side, you must lift the power steering reservoir up off its bracket. You'll see you need to do to remove it. Reconnect the top bracket with it's screw. First push it down towards the ground , then push it to the left as viewed from the outside-front of the car.
Wrong answer, I could have saved some time by reading my manual before I went shopping. Just unplug the old bulb and pop the new one in. The coolant reservoir, after removing the hold-down screw, comes out by pulling it straight up. My driver side headlight wire got loose so when i hit a bump at night if would flicker. On the other side you will need to remove the air filter box and connected parts. Answer Mike, I tried your advice, and it just doesn't … work.
It should slide right in and feel snug. Access the headlight located on the passenger side of the vehicle by removing the coolant overflow bottle. Please help support this website by shopping at. The hazard warning lamp will then flash. You need to replace them both. I put a mark on the cover before I took it off and then I put another mark on the lamp assembly, aligned with the mark on the cover, after I turned the cover to remove it. These bulbs should not be touched because the natural oils from fingers can ruin them! I put a mark on the cover before I took it off and then I put another mark on the lamp assembly, aligned with the mark on the cover, after I turned the cover to remove it.
See sources and related links below for replacement bulb information. Once located rotate bulb as far as it will go clockwise and re-fit wire connector and rubber boot. You may need to remove the battery for easyer reach. There is a separate cover for each headlight bulb. If you found this guide to be helpful, please consider making a small donation by clicking on the PayPal.
Nissan Altima Headlight Bulb Replacement Guide With Pictures - PaulsTravelPictures. One note: there is another intake path at the bottom of the air box. If you found this guide to be helpful, please consider making a small donation by clicking on the PayPal. Note: I am not a registered charity. The first picture in the row below is the Sylvania 55 Watt headlight bulb that was purchased for the swap.
Turn the locking collar counterclockwise to unlock, and remove. This is next to the coolant bottle. Good Luck and good motoring! I'd answer it myself, but I'm in the middle of doing it and finally gave up for the day. Strangest bulb I've ever seen, secured by a fancy spring clip and two screws, and widely spaced push-on terminals fed by individual wires. After comparing the bulbs to make sure they match, holding the new bulb by the plastic casing at the rear, insert the new bulb making sure the notches seat into the seating tabs. Push down on the black retaining clip and disconnect the bulb harness.
Flip the clip all the way up. Now you have access to the bulbs including the head light bulb. Safety First Then start working on one side and use the other side… Here is the best answer I found although I have not attempted the procedure. It was hinged at the bottom so it didn't go anywhere. Replacing the air box: 6 Align the air box's two pointed rubber connectors with their holes and push down hard. Position the new bulb in according to the locating tabs--concentrate on the 12 o'clock positioned locating pin. Oh yeah- you will have to re-program your radio after disconnecting the battery.
Oil from your fingers can severly shorten the life of the bulb. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. Loosen two caliper bolts they are facing in the brake caliper bolts are 14mm , then remove the caliper from around the rotor use a strong wire to hang the caliper to the spring so that the caliper is not hanging on the brake… Motor mount repair first necessitates the installation of a temporary support for the motor. The … ring is located about 8 inches from either end of the car. Note: Total time to remove everything, change the bulbs, and re-install was 15 minutes. Twist the socket a quarter turn counter clockwise, and pull out the socket. Re-set your clock and re-tune the radio.
If there is no ground plate you will only need to remove the hot wire from the base of the bulb leaving the ground wire in place 7 Put the bulb in and clip it in place being sure the metal clip is all the way up. Some said to drop the front bumper and others were tight on your hands. Driver Side: 1 Remove the 10 mm bolt that holds the air box down this is on the gold colored bracket on the driver-side fender. Rusty bolts on the fron of the car broke off. A five minute job once you have done it once but quite tricky first time! Instead there is a wire holder keeping the bulb in place. Then unhinge the air box and move the top of the air box up and out of the way.
For the driver's side, it recommends removing the battery to make some room in the 2004 book I would agree, after seeing mine. The 2005 Nissan Altima center high mount stop third 3rd brake light bulb replacement: Purchase the correct replacement center high mount stop third 3rd brake light bulb s first, before disassembling the vehicle. To be more precise, they are located on row 2, columns 2 and 3 column 1 being closest to the fender of the car. I did this so I could install aftermarket h. Unclip the hold down wire and move it out of the way.