Fit the belt over starting at the crank shaft and going up to the sprockets. Remove the broken belt---buy a Mazda book--study timing--and then replace belt. If you are solo, be very careful when puting the idler pulley on. You do that by loosening two bolts on the top end of the belt, next to the left of the most left spark plug, as you look towards the windshield. Check the alignment of the timing mark on the camshaft timing belt pulley.
The diamond shaped mark needs to align with the diamond shaped mark on the inside belt cover should be the aux or oil pully. The Aspire was the first subcompact to come with standard dual airbags-a feature that competitors had soon started to include in their car designs. Feel Free to contact me at FixYa. Remove the two 8mm nuts holding the starter to the bracket. Let me know if this helped or if you have additional information or questions. There you will find detailed instructions.
This is advice not from a professional---just a little more experienced novice like you. Try cranking the engine by turning the key as if to start. Every product Bando manufactures is consistent in uniform, high quality product that is competitive and efficient. Generally, the Aspire is an excellent car for small families and young drivers. Check the alignment of the timing marks. Again, use the socket wrench to turn the tension pulley far enough so the 97 Ford Aspire serpentine belt replacement can be wrapped around the pulley.
Some owners have replaced the O2 sensors, transmission fluid, and the filters, but the problem remains. Been there done it---Fun Fun! I would loosen up the motor mount and carefully jack up the engine. Maybe you should do a compression check on your engine-- It might be time to just remove and replace the engine. They both have a triangle mark and a diamond shaped mark. Remove the crankshaft pulley and remove the timing cover.
Disconnect the ignition wires from the spark plugs. It has the Belt Diagrams you will need. You need that friends of your's here. The vibration is usually observed while the car is set to ignition and while in idle mode. Align the second pair with the rear of a bump on the bottom of the oil sump. If timing belt fails it can cause serious engine damage so it's better to be safe than sorry. If it were me--I would unbolt the idler pulley--not the tension pulley.
Your best bet would be to purchase a Haynes manual. It is always smart… i believe the relay is on the drivers side behind the headlightby the inside of the fender in front of the fuse box there should be a bunch of wires there. If not i would say that is your problem. This this what is connected to the cap and rotor. Starting from the crankshaft timing belt pulley and working counterclockwise, position the timing belt in place while keeping it under tension. Once the 97 Ford Aspire serpentine belt replacement is around the tension pulley, release the socket wrench and allow the tension pulley to take up the slack on the Automotive Serpentine Belt Replacement.
If the timing belt broke when the vehicle is running, then you could end up with alot of problems such as the valves being bent. Attach the timing belt upper cover. Feel Free to contact me at FixYa. Kia Motors manufactured the body of the vehicle while Mazda took care of the car's engine and other parts. It's a hard job very tight space to work in.
You will see gas erupting from the fuel filter… What you need to do, loosen the axle nut jack up the car, take off both front wheels. This replacement unit is thoroughly fashioned to resemble the original drive belt mounted in your motor vehicle. Listen to not cause any damage to componets. More notably, the Aspire was the first in the lineup to have dual airbags and optional antilock brakes. Bad distributor The Ford Aspire distributor usually lasts at least 45,000 miles. It is easy job but a dirty one one of course.
Choose Bando Drive Belt to repair your engine system to the best possible operating condition. Remove the front motor mount located on the rightfender apron and support the engine … by the oil pan using a floor jack with a block of wood You will now be able to jackthe engine up and down as you need to. There is a good change the tension pulley will need to be moved farther for the 1997 Ford Aspire serpentine belt replacement because the old belt may have stretched. Install the accessory drive belt. However, it has some manufacturing flaws that you need to consider before purchasing. Assuming you have spark at the spark plugs, disconnect hose from fuel filter in the engine compartment on the drivers side adjacent the windshield area.
It has the Belt Diagrams you will need. Not surprisingly, the Aspire bore the designation Kia Avella for South Korean and international markets. Jack up the right front corner of the vehicle and place a jack stand to keep the right corner raised. The last model rolled off the assembly line in September 2007. The four-door version had a longer wheelbase than the other did.