Keep in mind that some clutch problems - such as a clutch pedal that is hard to press down or sinks down to the floorboard, or a transmission that unexpectedly pops out of gear - may be due to the clutch cable that is ready to fail. You might have to pop the pressure plate loose before you remove all the bolts. If an issue comes up or a part ought to be fixed, don't wimp out with a low-quality part. Get a pry bar between the transmission and engine block and pop the transmission loose. Last, I'm a little fuzzy on the Stillen flywheel option as it says it is only for the 2007 altima but that would put it in our model range so it is a bit confusing. Selector lever : “D” position Accelerator pedal position : 0.
What did you end up using for your clutch then?? Don't ignore signs of trouble - swing by AutoZone for the Sentra clutch set you need to get your Nissan back on track. As for other sites references it and the flywheel, those are all supplier sites that were under the impression that it would work or simply have old listings up. Right now within the next few weeks. I'd also replace the clutch line. Guiding a superbly styled Nissan, a responsive suspension architecture delivers a uniquely enjoyable highway ride. It won't move far, you just want to make sure it will move. Not sure they would cover the cost of dropping the engine though, assuming it is not needed.
I rough up both sides of the clutch disc and pressure plate with some 100 grit sand paper. Once the transmission is out of the way, you will see the pressure plate. Any help will be appreciated. I think that at this point I should mention you should get a mask to prevent breathing in the dust. You must have simple understand of your Sentra Clutch Slave Cylinder that you can find some problem correct in time. Got Nissan Sentra Clutch Problems? Apply some white lithium grease to the shaft the bearing rides on, the ball and pivot for the clutch fork, the area the clutch fork rides on the throwout bearing and the splines of the input shaft.
While holding the tool and clutch disc in position, tighten the pressure plat bolts in a diagonal pattern one turn at a time. Push the axle shaft in. You've got to get a vehicle brand that'll perform flawlessly for a long time and you can depend on a real Nissan. Is the inspection result normal? When the transmission is supported properly, remove the last bolt, 6. Yeah I could see how it might seem like a waste but sadly I had to replace my clutch before anything.
One of these is pretty obvious: the clutch engages and disengages much closer to the floorboard than it once did. One part of your Nissan Sentra is the Clutch Slave Cylinder. Then remove the transmission housing bolts 3, 4 and 5. Select Year for Nissan Sentra Clutch Slave Cylinder. Put a paint mark one bolt hole and a mark on the flywheel so you can position the flywheel the same way when you reinstall it. Keeping things even is the key here. Where can i buy a oem besides the dealership? Posted on Apr 27, 2009 Either it was not installed properly or.
Thanks for helping a noob. Thank you for the responses! Put the tool through the clutch disc and, with the pressure plate, put it into position. Other materials: Combination switch system symptoms Symptom Table Perform the data monitor of consult to check for any malfunctioning item. I do plan on adding some Mods to the car and am doing my research as best I can. The lighter you go from there, the noisier it will become. This part is also sometimes called Nissan Sentra Clutch Kits.
Also check the clutch pedal to make sure it did not become misalligned while it was diconnected. Nissan Sentra Replacement Clutch Information Small, sensible autos like the ergonomically-designed Nissan Sentra are designed to be kept in excellent condition so that they can continue demonstrating impressive levels of mileage. About the Nissan Sentra Clutch Replacement Cost The cost of the clutch by itself is not much. Identify the malfunctioning part from the agreed combination and repair or replace the part. Along with that, you wind up grinding the gears when attempting to shift.
It took most of the day with two people working on it so id say ask for quotes in other shops. Thanks for the advice on the clutch line. This replacement item is carefully designed to resemble the initial clutch kit installed on your car. Ive been searching but havent found a single person who have done their clutch replacement. I keep reading on sites that sell the kits and they say 2007-2010 altima 3. If so, how much did you end up spending? Thanks for the quick reply.
Has anyone with a 3. And a friend of mine who I deployed with lives in Tokyo now but also gives me a lot of advice. Disconnect the lower ball joints from the lower control arms. It's a major undertaking - but others have been there before you, and there are many resources available to help guide you through the process. I had to fork out 600 bucks for the work to be done I'm pretty sure Nissan would reimburse you if you took the supporting documentation for that recall. When you smell burning while traveling, it means your clutch needs an inspection. That is a relatively cheap and easy fix.
Usually a clutch is a long-lasting system, over time the clutch plate can become worn and need repair. The Nissan Sentra clutch replacement cost is actually pretty inexpensive - for the part itself, at least. A car or truck is only as good as its parts, and so the team of specialists here at PartsGeek is eager to help you find the right parts for any job. Apr 08, 2012 just cause the relay clicks and makes noise does not mean its working properly that relay provided you have the right one will engage the clutch and the chances of the clutch being bad are very slim so make sure that you have the right relay and get a replacement just for arguements sake and try it also when you select the air cond does the selector light to show that its working that also could be the problem now if the system is out of refriderant this could also be the problem. Jack the front of the vehicle as high as you safely can and be sure you use jack stands to support the vehicle. You'll also need a reliable hoist and help from at least one able bodied friend - because it will be necessary to take out either the engine or the transmission. Purchased it a year ago only to finally get it on and realize it didn't work then they told me it actually didn't fit and I got a refund.